2010 Cadillac Truck SRX FWD V6-3.0L Page 1979

2010 Cadillac Truck SRX FWD V6-3.0L Page 1979

P2147, P2150, P2153, P2156, P216B, or P216E

The ECM detects the injector high voltage supply circuit is shorted to ground for greater than 2 s.

P2148, P2151, P2154, P2157, P216C, or P216F

The ECM detects the injector high voltage supply circuit is shorted to voltage for greater than 2 s.

Action Taken When the DTC Sets

DTCs P2147, P2148, P2150, P2151, P2153, P2154, P2156, P2157, P216B, P216C, P216E, and P216F are Type A DTCs.

Conditions for Clearing the DTC

DTCs P2147, P2148, P2150, P2151, P2153, P2154, P2156, P2157, P216B, P216C, P216E, and P216F are Type A DTCs.

Diagnostic Aids

* Performing the fuel injector coil test may help isolate an intermittent condition. Refer to Fuel Injector Solenoid Coil Test (LAU) (See:

Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW)

(See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection).

* If the condition is intermittent, move the related harnesses and connectors, with the engine operating, while monitoring the scan tool Injector

Control Circuit Status parameters. An Injector Control Circuit Status parameter will change from OK or Not Run to Fault if there is a

condition with the circuit or a connection.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Fuel System Description (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and Operation/Fuel System

Description)Fuel System Description (LAU or LY7) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and

Operation/Fuel System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P2147, P2148, P2150, P2151, P2153, P2154, P2156, P2157, P216B,

P216C, P216E, or P216F should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.