B121110_N55_ENGINE_FUEL_SYSTEM_DFT_01_18_11. 2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) Technical Service Bulletin # 125506 Date: 110101
Fuel/Engine Controls - DTC's Set/Hard Start/Driveability
SI B12 55 06
Engine Electrical Systems
January 2011
Technical Service
This Service Information bulletin supersedes SI B12 55 06 dated December 2010.
[NEW]designates changes to this revision
SUBJECT
N54 - Diagnosis for DME FC 29DC/29F2/2FBF
MODEL
E90, E92 with N54 produced from 06/06
E93, E60, E61 with N54 produced from 03/07
E82, E88 with N54 from start of production
E71 X6 with N54 from start of production
E89, Z4 with N54 from start of production
F01, F02 with N54 from start of production
SITUATION I
The customer may complain of:
^ Excessive cranking time before the engine starts (5-6 seconds) on a cold start or afier a hot soak.
In most cases, diagnosis shows fault code 2FBF as the only fault stored in the DME with SES lamp illumination.
SITUATION II
The customer may complain of the following:
^ "Vehicle loses power while driving" or "Vehicle runs poorly".
^ The Service Engine Soon lamp may be illuminated.
Diagnosis shows fault code 29DC (Cylinder injection cut-out, pressure too low in high-pressure system) and/or 2FBF (Fuel pressure on-release
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 228
injection, pressure too low), and in some cases, also in conjunction with 29F1 (Fuel high-pressure, plausibility) and 29F2 (Fuel high-pressure, fuel
pressure undershot).
In some cases, misfire faults for various cylinders (e.g., FC 20D1, 29CF, 29D2, 29CE, 29D0, 29CC) are also stored in MSD80/M5D81.
CAUSE
Possible causes may include:
^ Sensitivity of injection pump (HDP) diagnostic software
^ Internal failure of a High-pressure Injection Pump (HDP)
^ Failure of an electric fuel pump or a clogged fuel filter
^ Failure of the low or high-pressure sensors
^ Defective fuel pressure check - valve/fuel pressure regulator
^ Failure of a volume control valve
^ Defective fuel injector
^ Intermittent electrical connection problem (wire and/or connector) in the fuel delivery system.
PARTS INFORMATION
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 229
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 230
WARRANTY INFORMATION
ATTACHMENTS
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 231
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 232
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 233
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 234
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 235
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 236
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 237
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 238
B125506_N54_ENGINE DIAGNOSTIC_FAULT_TREE_01_06_11
Correction For Situation I
CORRECTION FOR SITUATION I
For E90, E92, E93, E60, E61, E82, E88, and E71 vehicles where the customer complains of "Long Cranking Time" and fault code 2FBF is
stored in the DME with the SES illuminated, proceed as follows:
1. Use the current ISTA diagnosis software (2.22 or higher).
2. While observing the fuel pressure, activate the electric fuel pump for 20 seconds, using ISTA and the diagnostic query function (after the vehicle
test, select Control unit tree; DME; Call ECU functions; Diagnostic query; and Low pressure fuel pump with activation).
3. Immediately after electric pump activation, the pressure must reach at least 4.75 bars.
4. If the minimum threshold of 4.75 bars was not reached, further diagnose the low-pressure system using test module B1214_DI KDR, Fuel
Pressure Control (possibly defective electric fuel pump or fuel filter/pressure regulator).
5. [NEW] If the minimum threshold of 4.75 bars was reached, reprogram the vehicle with the current ISTA P version (ISTA/P 2.40.2 or higher). The
target integration levels should be:
E90, E92 and E93 - E89x-10-12-503 or higher
E60 and E61 - E060-10-12-501 or higher
E82 and E88 - E89x-10-12-503 or higher
E71 - E070-12-501 or higher
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 239
6. [NEW] IMPORTANT: When programming vehicles equipped with the MSD81 DME, make sure that the DME control module is marked for
programming in the measure plan (yellow mark in the control module tree and a "P" symbol). If the DME is not marked, you have to select it
manually for programming in the control module tree (click on the module and mark the "program" checkbox), and then determine the measures
plan.
7. [NEW] After programming the DME programmed number should be "7626000" or higher.
8. After programming, readapting the DME by means of a short test drive is recommended:
^ Bring the engine to the normal operating temperature.
^ Drive the vehicle at a speed of between 50-60 mph and engine speeds of 2,000-3,000 rpm for approximately 3 minutes (use manual gear shifting,
if needed).
^ Let the engine idle for approximately 5 minutes.
^ If possible, to confirm repair effectiveness, let the vehicle sit overnight and cold start it the next morning. Then let it idle for approximately 5
minutes.
For E89 vehicles where the customer complains of "Long Cranking Time" and only the fault code 2FBF is stored in the DME with the SES
illuminated, proceed as follows:
1. Install a calibrated manual fuel pressure gauge (e.g., P/N 83 30 0 491 260 pressure gauge from the K-L-Jetronic special tool kit P/N 83 30 0 491
259), connected with the three-way adapter tool 135 270, into the low-pressure fuel supply line as follows:
#1 - Three-way adapter tool (135 270)
#2 - Pressure gauge P/N 83 30 0 491 260
2. Use the current ISTA diagnosis software (2.22 or higher).
3. While observing the fuel pressure on the gauge, activate the electric fuel pump for 20 seconds, using ISTA and the component activation function
(after the vehicle test, select Control unit tree; DME; Call ECU functions; Component activation; and Fuel pump).
4. Immediately after electric pump activation, the pressure read from the manual gauge must reach at least 4.75 bars.
5. If the minimum threshold of 4.75 bars was not reached, further diagnose the low-pressure system using test module B1214_DI KDR, Fuel
Pressure Control (possibly defective electric fuel pump or fuel filter/pressure regulator).
6. [NEW] If the minimum threshold of 4.75 bars was reached, reprogram the vehicle with ISTA/P 2.40.2 (or higher). The target integration level
should be E89x-10-12-503 or higher
After programming, readapting the DME by means of a short test drive is recommended:
^ Bring the engine to the normal operating temperature.
^ Drive the vehicle at a speed of between 50-60 mph and engine speeds of 2,000-3,000 rpm for approximately 3 minutes (use manual gear shifting,
if needed).
^ Let the engine idle for approximately 5 minutes.
^ If possible, to confirm repair effectiveness, let the vehicle sit overnight and cold start it the next morning. Then let it idle for approximately 5
minutes.
Correction For Situation II
CORRECTION FOR SITUATION II
For E90, E92, E93, E60, E61, E82, E88, E89, and E71 vehicles where the customer complains of "Losing power when driving", fault codes
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 240
29DC/2FBF and/or 29F1/29F2 are stored in the DME with the SES illuminated; proceed as follows:
1. Use the current ISTA diagnosis software. Perform test module B1214_DI KDR (Fuel Pressure Control).
2. IMPORTANT: perform this step ONLY FOR E89 (Z4) vehicles (not equipped with the low fuel pressure system sensor):
Prior to execution of the High-pressure test module, install a calibrated manual fuel pressure gauge (e.g., P/N 83 30 0 491 260 pressure gauge from
the K-L-Jetronic special tool kit P/N 83 30 0 491 259), connected with the three-way adapter tool 135 270, into the low-pressure fuel supply line as
follows:
#1. - Three-way adapter tool (135270)
#2. - Pressure gauge P/N 83 30 0 491 260
3. Perform all applicable steps of the High-pressure Fuel test module B1214_DI KDR. Pay attention to all questions being displayed during
diagnosis and answer them correctly.
Important Note:
When comparing the measured fuel pressure with the engine running at idle speed, make sure to let the fuel pressure stabilize for approximately 60
seconds prior to the final reading. Otherwise, an implausible value (around 150 bars) is going to be entered into the test, resulting in inaccurate
diagnosis (defective high-pressure pump).
4. [NEW] After completion of all diagnostic steps, end the test module and enter the "fault feedback" screen. Enter the result of a diagnosis process
into the Diagnosis Code dialog box and obtain a "Diagnostic Code". In case no failure can be currently detected in the high-pressure fuel system,
enter the last option "No fault found" into the dialog box.
IMPORTANT DIAGNOSTIC HINT:
In certain cases, the HDP fault may be reproduced only when the engine is under load. In order to replicate the complaint, it may be necessary to
road-test vehicle with the manual fuel pressure gauge installed. The excessive low-pressure fuel fluctuation (between 5.0 and 7.0 bars) would
indicate incorrect operation of the fuel delivery system.
5. [NEW] For additional comprehensive N54 drivability diagnostic information, refer to the "N54 Engine Diagnostic Fault Tree" (the current version
"01_06_11" is shown in this bulletin).
6. Make sure that FASTA data is transmitted after the completion of all appropriate test modules.
7. IMPORTANT: Starting on November 1st, 2010, TC authorization is NOT required for the HDP pump replacement. For details related to the
"N54 Fuel System TC Action", refer to SI B13 08 09.
8. If the High-pressure Fuel Pump needs to be replaced, use the updated part P/N 13 51 7 613 933, which incorporates the latest improvements to
internal sealing. For the pump replacement procedure, refer to REP 13 51 017.
Note:
The repair instructions have been updated with the release of the special tool P/N 83 30 0 496 939. The special tool accommodates easy removal of
the engine harness block, located under the intake manifold. Consequently, the removal of the intake manifold is no longer necessary when replacing
the HDP on the N54 engine.
9. After replacement, clear the adaptation values of the high-pressure flow control valve in the DME by selecting the path:
^ Activities / Service Functions
^ Drive
^ Motor Electronics
^ Adjustment Programs
2010 BMW 335Cic Convertible (E93) L6-3.0L Turbo (N54) 241
^ Delete Adaptations / variants, and then Test plan
^ Reset adaptive values.
10. [NEW] IMPORTANT NOTE: In addition, vehicles which have had the HDP pump replaced have to be reprogrammed afterwards with ISTA/P
2.40.2 (or higher). The target integration levels should be:
E60 and E61 - E060-10-12-501 or higher
E82, E88, E89, E90, E92, and E93 - E89x-10-12-503 or higher
E71-E070-10-12-501 or higher
IMPORTANT:
When programming vehicles equipped with the MSD81 DME, make sure that the DME control module is marked for programming in the measure
plan (yellow mark in the control module tree and a "P" symbol). If the DME is not marked, you have to select it manually for programming in the
control module tree (click on the module and mark the "program" checkbox), and then determine the measures plan. After programming, the DME
programmed number should be "7626000" or higher.
11. After programming, readapting the DME by means of a short test drive is recommended:
^ Bring the engine to the normal operating temperature.
^ Drive the vehicle at a speed of between 50-60 mph and engine speeds of 2,000-3,000 rpm for approximately 3 minutes (use manual gear shifting,
if needed).
^ Let the engine idle for approximately 5 minutes.
^ If possible, to confirm repair effectiveness, let the vehicle sit overnight and cold start it the next morning. Then let it idle for approximately 5
