Mercedes Benz Truck GLK 350 Technical Problem # LI42-20_P-052990 Date: 120117
Brakes - Squeak, Scrape, Or Rattle From Rear Brakes
Squeaking, scraping or rattling noises from area of rear wheel brake without brake actuation
Topic number LI42.20-P-052990
Version 1
Design group 42.20 Parking brake
Date 01-17-2012
Validity Model 204/207
Reason for change
Complaint:
Squeaking, scraping or rattling noises from area of rear wheel brake without brake actuation.
Attachments
Cause:
1. Brake shoes of the parking brake touch the inside of the brake disk bowl in the axial direction.
The brake shoes of the parking brake are fastened to the cover panel with retaining springs. These retaining springs must be centered on the
elongated holes in the brake shoes. If this is not the case, the affected brake shoe may touch the lip of the brake disk bowl in the axial direction
and cause noises (see attachment 1).
2. Stator clip has slipped and touches the inside of the brake disk bowl in the axial direction.
A stator clip is pushed onto the support for the brake shoes of the parking brake (brake stator). This prevents the brake shoes from working
into the aluminum wheel carrier. If this clip is pushed too far on during assembly, it may be widened in the radius area of the brake stator (see
attachment 2, item 3). This widening means that permanent secure fastening of the stator clip is no longer guaranteed and it may wander from
the brake stator in the axial direction until it touches the lip of the brake disk bowl.
3. Expansion lock has play.
The expansion lock is designed to have sufficient component tolerance to guarantee proper functioning of the parking brake even when
covered with brake dust deposits in the course of operation. This play can cause rattling noises on rough roads.
Remedy:
Re. 1. Brake shoes:
Replacement of the silver-colored brake shoe retaining springs installed as standard for black retaining springs (see parts ordering note).
When installing the retaining springs, the following points must be observed:
Mercedes Benz Truck GLK 350 49
^Use of installation tool W 112 589 09 61 00 (see attachment 3).
^ Insert the retaining springs through the cutouts in the rear axle shaft flange so that they can be mounted vertically on the brake shoes (see
attachment 4).
^ Center the retaining springs on the elongated holes in the brake shoes (see attachment 5).
^ To hook up the retaining springs in the cover panel, turn them counterclockwise (to the left) to prevent tilting and to avoid stresses.
Re. 2. Stator clip:
Check the stator clip for abrasion marks and correct seating on the brake stator (see attachment 2, item 1: The sides of the stator clip must be
flush with the brake stator). If abrasion marks are visible on the stator clip, or if it is installed incorrectly, the stator clip must be replaced.
Re. 3. Expansion lock:
Install an additional snap clip between the extension spring and the expansion lock as per the installation note (see attachment 6, Figure 1).
When installing, please not:
^ Position the snap clip in the center of the extension spring and make sure that it engages properly in the extension spring (see attachment 6,
Figure 2).
Attachments
Symptoms
Parts
Mercedes Benz Truck GLK 350 50
Attachment 1
Mercedes Benz Truck GLK 350 51
Attachment 2
Mercedes Benz Truck GLK 350 52
Attachment 3
Mercedes Benz Truck GLK 350 53
Attachment 4
Mercedes Benz Truck GLK 350 54
Attachment 5
Mercedes Benz Truck GLK 350 55
Attachment 6
Brakes - Squeak, Scrape, Or Rattle From Rear Brakes
Squeaking, scraping or rattling noises from area of rear wheel brake without brake actuation
Topic number LI42.20-P-052990
Version 1
Design group 42.20 Parking brake
Date 01-17-2012
Validity Model 204/207
Reason for change
Complaint:
Squeaking, scraping or rattling noises from area of rear wheel brake without brake actuation.
Attachments
Cause:
1. Brake shoes of the parking brake touch the inside of the brake disk bowl in the axial direction.
The brake shoes of the parking brake are fastened to the cover panel with retaining springs. These retaining springs must be centered on the
elongated holes in the brake shoes. If this is not the case, the affected brake shoe may touch the lip of the brake disk bowl in the axial direction
and cause noises (see attachment 1).
2. Stator clip has slipped and touches the inside of the brake disk bowl in the axial direction.
A stator clip is pushed onto the support for the brake shoes of the parking brake (brake stator). This prevents the brake shoes from working
into the aluminum wheel carrier. If this clip is pushed too far on during assembly, it may be widened in the radius area of the brake stator (see
attachment 2, item 3). This widening means that permanent secure fastening of the stator clip is no longer guaranteed and it may wander from
the brake stator in the axial direction until it touches the lip of the brake disk bowl.
3. Expansion lock has play.
The expansion lock is designed to have sufficient component tolerance to guarantee proper functioning of the parking brake even when
covered with brake dust deposits in the course of operation. This play can cause rattling noises on rough roads.
Remedy:
Re. 1. Brake shoes:
Replacement of the silver-colored brake shoe retaining springs installed as standard for black retaining springs (see parts ordering note).
When installing the retaining springs, the following points must be observed:
Mercedes Benz Truck GLK 350 49
^Use of installation tool W 112 589 09 61 00 (see attachment 3).
^ Insert the retaining springs through the cutouts in the rear axle shaft flange so that they can be mounted vertically on the brake shoes (see
attachment 4).
^ Center the retaining springs on the elongated holes in the brake shoes (see attachment 5).
^ To hook up the retaining springs in the cover panel, turn them counterclockwise (to the left) to prevent tilting and to avoid stresses.
Re. 2. Stator clip:
Check the stator clip for abrasion marks and correct seating on the brake stator (see attachment 2, item 1: The sides of the stator clip must be
flush with the brake stator). If abrasion marks are visible on the stator clip, or if it is installed incorrectly, the stator clip must be replaced.
Re. 3. Expansion lock:
Install an additional snap clip between the extension spring and the expansion lock as per the installation note (see attachment 6, Figure 1).
When installing, please not:
^ Position the snap clip in the center of the extension spring and make sure that it engages properly in the extension spring (see attachment 6,
Figure 2).
Attachments
Symptoms
Parts
Mercedes Benz Truck GLK 350 50
Attachment 1
Mercedes Benz Truck GLK 350 51
Attachment 2
Mercedes Benz Truck GLK 350 52
Attachment 3
Mercedes Benz Truck GLK 350 53
Attachment 4
Mercedes Benz Truck GLK 350 54
Attachment 5
Mercedes Benz Truck GLK 350 55
Attachment 6
