Tuesday, March 15, 2022

2010 Cadillac Truck SRX FWD V6-3.0L Page 1058

2010 Cadillac Truck SRX FWD V6-3.0L Page 1058



4. Command the appropriate Camshaft Position Actuator Solenoid Valve ON with a scan tool. Load test for less than 1 V between the control



circuit terminal 2 and ground.



瀚慖f greater than the specified range, test the control circuit for an open/high resistance. If the circuit/connections test normal, replace the



K20 Engine Control Module.



5. Remove the Camshaft Position Actuator Solenoid Valve. Inspect the Camshaft Position Actuator Solenoid Valve and mounting area for the



following conditions:



* For a torn, restricted, mis-positioned, or missing screens at the Camshaft Position Actuator Solenoid Valve



* For engine oil leaks between the oil sealing lands of the Camshaft Position Actuator Solenoid Valve. Inspect the lands of the Camshaft



Position Actuator Solenoid Valve for nicks



* For oil seepage at the Camshaft Position Actuator Solenoid Valve connector



瀚慖f a condition is found, replace Q6 Camshaft Position Actuator Solenoid Valve.



6. Ignition OFF, swap the appropriate Camshaft Position Actuator Solenoid Valve with a Camshaft Position Actuator Solenoid Valve that is



operating correctly.



7. Engine idling. Command the appropriate Camshaft Position Actuator from 0 degrees to 40 degrees and back to zero while observing the



appropriate scan tool Camshaft Position Variance parameters. The Camshaft Position Variance should be less than 2 degrees in each of the



commanded states.



瀚慖f greater than the specified value, replace the mechanical camshaft position actuator.



8. If all circuits/connections test normal, test or replace the Q6 Camshaft Position Actuator Solenoid Valve.



Component Testing



1. Ignition OFF, disconnect the harness connector at the appropriate Q6 Camshaft Position Actuator Solenoid Valve.



2. Test for 7-12 ohm between the control terminal 2 and the ignition terminal 1 of the Q6 Camshaft Position Actuator Solenoid Valve.



瀚慖f not within the specified range, replace the Q6 Camshaft Position Actuator Solenoid Valve.



3. Test for infinite resistance between each terminal and the Q6 Camshaft Position Actuator Solenoid Valve housing.



瀚慖f not the specified value, replace the Q6 Camshaft Position Actuator Solenoid Valve.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Camshaft Position Actuator Replacement - Bank 1 (LF1) (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and Push



Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 1)



* Camshaft Position Actuator Replacement - Bank 2 (LF1) (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and Push



Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 2)



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 1 (Right Side) Intake)



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust)



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 2 (Left Side) Intake)



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming, and setup



P052D



DTC P052B, P052D, P054B, or P054D



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.

No comments:

Post a Comment