2010 Cadillac Truck SRX FWD V6-3.0L Page 1468

2010 Cadillac Truck SRX FWD V6-3.0L Page 1468

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine running, observe the following scan tool control circuit status parameters for the appropriate cylinder T8 ignition coil:

* Ignition Coil 1-6 Control Circuit Low Voltage Test Status

* Ignition Coil 1-6 Control Circuit Open Test Status

* Ignition Coil 1-6 Control Circuit High Voltage Test Status

Each parameter should display Not Run or OK.

2. Engine idling, observe the DTC information with a scan tool. DTC P0351, P0352, P0353, P0354, P0355, or P0356 should not set.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate T8 ignition coil.

2. Ignition OFF, and all vehicle systems OFF, it may take up to 2 minutes for all the systems to power down. Test for less than 5 ohm between

the ground circuit terminal A and ground.

瀚慖f greater than the specified range, repair the ground circuit for an open/high resistance.

3. Ignition OFF, test for less than 5 ohm between the low reference circuit terminal B and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

4. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal D and ground.

瀚慖f the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests

normal and the ignition voltage circuit fuse is open, test all components connected to the ignition voltage circuit and replace as necessary.

5. Engine running, observe the Ignition Coil 1-6 Control Circuit Low Voltage Test Status on the scan tool. Test Status should be Ok or Not

Run.

瀚慖f test status is Malfunction test for open or short to ground.

6. Engine running, observe the Ignition Coil 1-6 Control Circuit Open Test Status on the scan tool. Test Status should be Ok or Not Run.

瀚慖f test status is Malfunction test for open circuit.

7. Engine running, observe the Ignition Coil 1 6 Control Circuit High Voltage Test Status on the scan tool. Test Status should be Ok or Not

Run.

瀚慖f test status is Malfunction test for short to voltage.

8. If all circuits test normal, test or replace the T8 ignition coil.

Repair Instructions

* T8 Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil

Replacement - Bank 1)

* T8 Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil

Replacement - Bank 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

Repair Verification

Note: An ignition control circuit fault condition will result in an engine misfire, and under certain driving conditions could possibly overheat the

3-way catalytic converter.

1. Install any components or connectors that have been removed or replaced during diagnosis.

2. Perform any adjustment, programming, or setup procedures that are required when a component or module is removed or replaced.

3. Clear the DTCs.

4. Turn the ignition OFF for 60 s.

5. If the repair is related to a DTC, duplicate the Conditions for Running the DTC and use the Freeze Frame/Failure Records, if applicable, in

order to verify the DTC does not reset. If the DTC resets or another DTC is present, refer to Diagnostic Trouble Code (DTC) List - Vehicle

(See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) and perform the appropriate diagnostic