Wednesday, May 19, 2021

2010 Cadillac CTS Sedan AWD V6-3.6L Page 880

2010 Cadillac CTS Sedan AWD V6-3.6L Page 880



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views)



Description and Operation



Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft



Actuator System Description)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit



Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Testing



1. Ignition ON, observe the DTC information with a scan tool. Verify that none of the following DTCs are set. DTC P0010, P0013, P0020,



P0023, P0335, P0336, P0338, P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, P0393, P2088, P2089,



P2090, P2091, P2092, P2093, P2094, or P2095.



瀚慖f any of the DTCs listed are set refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code



Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for further diagnosis.



2. Idle the engine at normal operating temperature for 10 minutes. DTCs P0016, P0017, P0018, or P0019 should not set.



瀚慖f a DTC sets, inspect for the following and repair as necessary:



* The correct installation of the camshaft sensors



* The correct installation of the crankshaft sensor



* A timing chain tensioner condition



* An incorrectly installed timing chain



* Excessive play in the timing chain



* A mechanical cam actuator that is stuck in the full advance or retard position.



* A timing chain that jumped teeth



* A crankshaft reluctor wheel that has moved in relationship to top dead center (TDC) on the crankshaft



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Timing Chain Alignment Diagram (See: Engine, Cooling and Exhaust/Engine/Timing Components/Timing Component Alignment



Marks/Locations)



* Camshaft Timing Drive Components Cleaning and Inspection (See: Engine, Cooling and Exhaust/Engine/Service and Repair/Overhaul/67.



Camshaft Timing Drive Components Cleaning and Inspection)



* Crankshaft and Bearing Cleaning and Inspection (See: Engine, Cooling and Exhaust/Engine/Service and Repair/Overhaul/52. Crankshaft



and Bearing Cleaning and Inspection)



P16F3



DTC P0601-P0604, P0606, P0607, P0610, P062B, P062F, P0630, P16F3, or P2610 (ECM, LF1)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.

No comments:

Post a Comment