2010 Cadillac CTS Sedan AWD V6-3.6L Page 778

2010 Cadillac CTS Sedan AWD V6-3.6L Page 778

* The engine is operating for greater than 1 seconds.

* The engine speed is greater than 520 RPM.

* The engine must accelerate such that the CMP actuator system is commanded from the park position to the phased position. This is

considered a cam control cycle. There must be a minimum of 2 cam control cycles for at least 2.5 seconds each in the phased position.

* DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021, and P0024 run continuously once the above conditions are met for greater than

600 seconds.

Conditions for Setting the DTC

* The ECM detects the difference between the desired camshaft position angle and the actual camshaft position angle is greater than 7-8

degrees.

OR

* The ECM detects a slow response, a deviation greater than 1.5 degrees in time greater than 2 seconds, for the actual camshaft position angle

to match the desired position angle during the test.

* Either condition exists for greater than 1 second or a cumulative of 10 seconds.

Action Taken When the DTC Sets

DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021, and P0024 are type B DTCs.

Conditions for Clearing the DTC

DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021, and P0024 are type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft

Actuator System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

* J 35616-200 - Test Lamp Kit

* For equivalent regional tools, refer to Special Tools (See: Powertrain Management/Computers and Control Systems/Tools and Equipment).

Diagnostic Aids

* The engine oil condition has a major impact on the camshaft actuator system.

* A low oil level condition may set this DTC. The engine may require an oil change. Inquire with the customer when the last oil change was

performed. You may also monitor the scan tool Engine Oil Life parameter. Advise the customer an oil change may be required.

* Inspect the engine for any recent engine mechanical repairs. An incorrectly installed camshaft, camshaft actuator, or timing chain can cause

this DTC to set.

Circuit/System Verification

Note: The engine oil level and the oil pressure are critical to the correct operation of the camshaft position (CMP) actuator system. Verify

that the engine has the correct oil level and the correct oil pressure before continuing with this diagnostic.

1. Ignition ON, observe the scan tool DTC information. Verify that DTC P0016, P0017, P0018, P0019, P0335, P0336, P0338, P0341, P0342,