2010 Cadillac CTS Sedan AWD V6-3.6L Page 359

-

2010 Cadillac CTS Sedan AWD V6-3.6L Page 359



Conditions for Clearing the DTC



* The condition for setting the DTC no longer exists.



* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.



Reference Information



Schematic Reference



SIR Schematics (See: Diagrams/Electrical Diagrams/Air Bag Systems)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views)



Description and Operation



SIR System Description and Operation (See: Restraints and Safety Systems/Air Bag Systems/Description and Operation/SIR System Description



and Operation)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit



Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.



Circuit/System Testing



Important: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or



replacement of the affected.



* SDM



* SDM wiring harness



1. Ignition ON, verify DTC B1370 is not set in any other control modules.



瀚慖f the DTC is set in any other control module, refer to DTC B1370-B1379, B1380-B1389, or B1440-B1443 ( See: B Code Charts/B1370



).



2. Ignition OFF, disconnect the harness connector at the SDM.



3. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 32 and ground.



瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open high resistance.



4. If all circuits test normal, replace the SDM.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* SIR/SRS Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/SIR/SRS Wiring Repairs)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for SDM replacement, setup, and programming



Wiring Systems and Power Management



DTC B1370-B1379, B1380-B1389, or B1440-B1443



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

-
P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

-
Image
  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Read more

The BMW M5 Sedan & M5 Touring with BMW M Performance Parts.

-
Image
 BMW (Benz-Wesbach) is a well-known and respected luxury brand in the European automotive market, particularly for sports cars like the M5. However, unlike some other car manufacturers, BMW has not primarily focused on its formula racing or sport engineering heritage. Instead, the BMW M series has been a strong seller due to their sportiness, reliability, and aesthetic appeal. If you're referring to BMW's M5 sedan **and touring variant** with performance parts, here are some key points to consider: 1. **Performance Improvement**:     - BMW’s sports cars, including the M5 models, have improved over previous iterations. The 3.0 liter straight-6 power plant in the M5 has seen improvements like a new torque vectoring system and increased engine robustness. These upgrades can enhance acceleration and cornering stability compared to older versions of the car. 2. **Eco-Friendly Parts**:    - BMW is known for introducing eco-friendly components, particularly in veh...
Read more