2010 Cadillac CTS Sedan AWD V6-3.6L Page 66

-

2010 Cadillac CTS Sedan AWD V6-3.6L Page 66



Instructions)provides an overview of each diagnostic category.



DTC Descriptor



DTC B0005 00



- In Park Switch Circuit



Circuit/System Description



The body control module (BCM) supplies the park enable signal circuit voltage when the vehicle transmission is in Park.



Conditions for Running the DTC



The system voltage is between 9-16 volts.



Conditions for Setting the DTC



The BCM detects there is a short to ground for greater than 5 seconds.



Action Taken When the DTC Sets



The BCM will not supply voltage to the circuit.



Conditions for Clearing the DTC



* The current DTC will clear when the malfunction is no longer present.



* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.



Reference Information



Schematic Reference



Body Control System Schematics (See: Body and Frame/Body Control Systems/Diagrams/Electrical Diagrams)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit



Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning)for Scan Tool Information



Circuit/System Testing



1. Ignition OFF, disconnect the X5 harness connector at the BCM.



2. Verify there is no aftermarket component wired to terminal 19.



瀚慖f there is an aftermarket component wire, test the circuit terminal for a short to ground. If the circuit tests normal, replace the BCM.



3. If all circuits test normal, replace the BCM.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Body Control Module Replacement (See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair/Body Control



Module Replacement)



* Control Module References (See: Testing and Inspection/Programming and Relearning)for module replacement, setup, and programming



B009A



DTC B009A



Diagnostic Instructions

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

-
P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

-
Image
  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Read more

The BMW M5 Sedan & M5 Touring with BMW M Performance Parts.

-
Image
 BMW (Benz-Wesbach) is a well-known and respected luxury brand in the European automotive market, particularly for sports cars like the M5. However, unlike some other car manufacturers, BMW has not primarily focused on its formula racing or sport engineering heritage. Instead, the BMW M series has been a strong seller due to their sportiness, reliability, and aesthetic appeal. If you're referring to BMW's M5 sedan **and touring variant** with performance parts, here are some key points to consider: 1. **Performance Improvement**:     - BMW’s sports cars, including the M5 models, have improved over previous iterations. The 3.0 liter straight-6 power plant in the M5 has seen improvements like a new torque vectoring system and increased engine robustness. These upgrades can enhance acceleration and cornering stability compared to older versions of the car. 2. **Eco-Friendly Parts**:    - BMW is known for introducing eco-friendly components, particularly in veh...
Read more