2010 Cadillac CTS Sedan AWD V6-3.6L Page 1095

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1095

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine idling, observe the appropriate scan tool HO2S 1 voltage parameter. The voltage should fluctuate above and below the range of

350-550 mV.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate HO2S.

2. Ignition ON, verify that the scan tool HO2S voltage parameter is between 350-500 mV.

瀚慖f less than the specified range, test the signal circuit terminal B for a short to ground. If the circuit/connections test normal, replace the

ECM.

瀚慖f greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit/connections test normal, replace

the ECM.

3. Install a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the scan tool HO2S voltage parameter is less than 60

mV.

瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit/connections test normal, replace the

ECM.

4. Connect a 3 A fused jumper wire between the signal circuit terminal B and the low reference circuit terminal A. Verify the scan tool HO2S

voltage parameter is less than 60 mV.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the

circuit/connections test normal, replace the ECM.

5. Verify that the following conditions do not exist:

* Leaking fuel injectors.

* High fuel system pressure-Refer to Fuel System Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and

Inspection/Component Tests and General Diagnostics/Fuel System Diagnosis).

* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool) (See: Powertrain

Management/Computers and Control Systems/Testing and Inspection/Component Tests and General

Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (without Special

Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General

Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (without Special Tool)).

* Restricted exhaust.

瀚慖f you find any of the above conditions, repair as necessary.

6. If all circuits/connections test normal, replace the appropriate HO2S.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)