2010 Cadillac CTS Sedan AWD V6-3.6L Page 853

2010 Cadillac CTS Sedan AWD V6-3.6L Page 853

401-519 mV.

3. Observe the DTC information with a scan tool. DTC P013A, P013C, P013E, and P014A should not set.

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate HO2S.

2. Ignition ON, verify that the scan tool HO2S voltage parameter is between 400-520 mV.

瀚慖f less than the specified range, test the signal circuit terminal B for a short to ground. If the circuit/connections test normal, replace the

ECM.

瀚慖f greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit/connections test normal, replace

the ECM.

3. Connect a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the scan tool HO2S voltage parameter is less than

60 mV.

瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit/connections test normal, replace the

ECM.

4. Connect a 3 A fused jumper wire between the signal circuit terminal B and the low reference circuit terminal A. Verify the scan tool HO2S

voltage parameter is less than 60 mV.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the

circuit/connections test normal, replace the ECM.

5. Verify that none of the following conditions exist:

* Lean or rich condition.

* Water intrusion in the HO2S harness connector

* HO2S wiring harness damage

* Incorrect RTV sealant

* Low or high fuel system pressure-Refer to Fuel System Diagnosis (See: Powertrain Management/Computers and Control

Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel System Diagnosis).

* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool) (See: Powertrain

Management/Computers and Control Systems/Testing and Inspection/Component Tests and General

Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (without Special

Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General

Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (without Special Tool)).

* Fuel saturation of the evaporative emission (EVAP) canister

* Exhaust leaks near the HO2S

* Engine vacuum leaks

* Engine oil consumption

* Engine coolant consumption

瀚慖f you find any of the above conditions, repair as necessary.

6. If all conditions test normal, replace the appropriate HO2S.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and

programming

P013B

DTC P0133, P013A-P013F, P014A, P014B, P0153, P1133, or P1153 (LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System