Friday, October 30, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1737

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1737

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P079B

- Transmission Clutch 2 Slip Detected

Circuit/System Description

The transmission control module monitors hybrid direct, 2-3-4 clutch slip speed when the hybrid direct, 2-3-4 clutch is applied. The hybrid direct,

2-3-4 clutch is displayed as Clutch 2 on the scan tool. The transmission control module is part of the control solenoid valve assembly and is not

serviced separately.

Conditions for Running the DTC

* Hybrid direct, 2-3-4 clutch is applied.

* The clutch pressure control solenoid 3 commanded pressure is 1800 kPa (261 psi) for 3 seconds.

Conditions for Setting the DTC

The transmission control module detects the hybrid direct, 2-3-4 clutch slip speed is greater than 200 RPM for 3 seconds.

Action Taken When the DTC Sets

* P079B is a Type B DTC.

* The transmission control module inhibits gear 2, gear 3, gear 4 and EVT 2.

Conditions for Clearing the DTC

P079B is a Type B DTC.

Diagnostic Aids

When attempting to set transmission performance DTCs, observe the Freeze Frame and Failure Records to assist in duplicating the failure

conditions. Ensure the transmission fluid level is correct and there are no leaks. If there are any other transmission DTCs set, diagnose those first.

Reference Information

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

1. Verify that DTCs P0721, P0722, P0723, P0966, P0967, P0969, P0970, P0971, P0973, P0974, P0976, P0977, P2720, P2721, P2728, P2729,

or P2730 is not set.

瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing

and Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Transmission Fluid Level and Condition Check)

to verify correct fluid level.

3. Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component

Tests and General Diagnostics/2ML70 - Automatic Transmission/Line Pressure Check) to verify correct oil pressure.

4. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control

Solenoid Valve and Transmission Control Module Assembly Inspection) to verify control solenoid valve assembly condition.

5. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (See: Transmission and

Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic

Transmission/Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test) to verify control solenoid

valve assembly function.

6. Inspect the trans fluid pump ball check valve for possible sticking or damage.

瀚慖f the check ball is stuck or damaged, replace the check ball.

7. Inspect the hybrid direct, 2-3-4 clutch regulator valve for sticking or damage.

瀚慖f you found a concern with the hybrid direct, 2-3-4 clutch regulator valve, repair or replace the valve or valve body.

No comments:

Post a Comment