2010 Cadillac CTS Sedan AWD V6-3.0L Page 1867

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1867

The ECM detects the injector high voltage supply circuit is shorted to voltage for greater than 2 s.

Action Taken When the DTC Sets

DTCs P2147, P2148, P2150, P2151, P2153, P2154, P2156, P2157, P216B, P216C, P216E, and P216F are Type A DTCs.

Conditions for Clearing the DTC

DTCs P2147, P2148, P2150, P2151, P2153, P2154, P2156, P2157, P216B, P216C, P216E, and P216F are Type A DTCs.

Diagnostic Aids

* Performing the fuel injector coil test may help isolate an intermittent condition. Refer to Fuel Injector Solenoid Coil Test (w/LLT) (See:

Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector

Solenoid Coil Test)Fuel Injector Solenoid Coil Test (w/LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Injector/Testing and Inspection).

* If the condition is intermittent, move the related harnesses and connectors, with the engine operating, while monitoring the scan tool Injector

Control Circuit Status parameters. An Injector Control Circuit Status parameter will change from OK or Not Run to Fault if there is a

condition with the circuit or a connection.

Reference Information

Schematic Reference

Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Fuel System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Fuel System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P2147, P2148, P2150, P2151, P2153, P2154, P2156, P2157, P216B,

P216C, P216E, or P216F should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X109 or X110, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.