2010 Cadillac CTS Sedan AWD V6-3.0L Page 1603

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1603

Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. DTC P0641, P0651, P0697, or P06A3 should not set.

2. Observe the appropriate scan tool 5 V Reference Circuit Test Status parameter. The parameter should display OK or Not Run.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: Additional DTCs will set when disconnecting the components.

1. Ignition OFF, disconnect the harness connector of all appropriate sensors for the applicable DTC. Refer to Diagnostic Aids.

2. Ignition ON, test for 4.6-5.2 V between each of the affected 5 V reference circuits and ground.

瀚慖f the voltage is less than the specified range, test for a short to ground or for an open between the ECM and the affected circuit splice. If

the circuit tests normal, replace the K20 ECM.

瀚慖f the voltage is greater than the specified range, test for a short to voltage on the 5 V reference circuit. If the circuit tests normal, replace

the K20 ECM.

Note: A short to voltage on the signal circuit of certain components may cause this DTC to set.

3. Connect each component associated with the affected 5 V reference circuit one at a time while monitoring the appropriate scan tool 5 V

Reference Circuit Status parameter. The parameter should continue to display OK.

瀚慖f the parameter displays Fault when a component is connected, test the signal circuit of that component for a short to voltage. If the

circuit tests normal, replace the component.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Tank Pressure Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Fuel Tank Pressure Sensor/Service

and Repair)

* Barometric Pressure Sensor Replacement (LF1) (See: Powertrain Management/Computers and Control Systems/Barometric Pressure

Sensor/Service and Repair)

* Fuel Pressure Sensor Replacement - Fuel Injection Fuel Rail (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Pressure Sensor/Switch/Service and Repair)Fuel Pressure Sensor Replacement - Fuel Injection Fuel Rail (LLT) (See: Powertrain

Management/Fuel Delivery and Air Induction/Fuel Pressure Sensor/Switch/Service and Repair)

* Engine Oil Pressure Sensor and/or Switch Replacement (See: Engine, Cooling and Exhaust/Engine/Engine Lubrication/Oil Pressure

Sensor/Service and Repair)

* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake)

* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust)