Thursday, August 15, 2019

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S303-09 Date: 020701

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # S303-09 Date: 020701



Engine Control - MIL ON, P1383 or P1388



S303-09



S-TYPE



DATE 07/02



MODEL



2000-02 MY



S-TYPE 3.0L



2000 Jaguar S-Type (X200) V6-3.0L Page 96



VIN



L00001-M44997



MIL Illuminated - 3.0L V6 - False Flagging of DTC P1383 or P1388 - Reprogram PCM



Issue:



Some 2000-01 MY S-TYPE vehicles may experience illumination of the MIL with DTCs P1383 or P1388 (over retarded camshaft timing) stored.



To eliminate the false flagging of DTCs P1383 and P1388, the Powertrain Control Module (PCM) should be re-programmed using WDS software



release JTP759/14 or later.



Note:



The PCM is described as the ECM when using WDS.



When entering the ECM re-configuration section the user will be prompted to determine the engine serial number of the vehicle.



If the first six digits of the engine number are outside the specified serial number range (103981*** to 127908***) the user will be allowed through



to re-calibrate the vehicle PCM with a standard set of calibrations.



If the engine serial number falls within the given range the system will automatically divert to a more aggressive set of calibrations.



Action:



In case of a customer complaint of the above condition on a 2000-01 MY S-TYPE vehicle within the above VIN range, follow the workshop



procedure outlined below.



PCM REPROGRAMMING PROCEDURE



Note:



The engine number is located on the bar code label on the engine front cover (Illustration 1) or on the left-hand side of the engine bedplate



(Illustration 2). Position the vehicle on a lift as needed to gain access.



1. Open hood and cover fenders.



2000 Jaguar S-Type (X200) V6-3.0L Page 97



Note:



Use WDS software JTP 759/14 or later.



2. Position the WDS alongside vehicle, switch "ON" Portable Test Unit (PTU) and allow software to load.



3. Connect the PTU to the vehicle data link connector (DLC) via diagnostic cable.



4. Enter the VIN and navigate to content model screen, select engine system, and then go to DTC monitor.



5. Read engine DTCs, if any stored clear from memory



Note:



If any DTCs are stored, determine the fault and carry out on a separate Warranty claim.



6. Navigate to configuration main menu; select and run "re-configure existing ECM".



Note:



While WDS is re-programming PCM, apply generic update label (JJM 998499/20) alongside the VCATS label in the trunk with revised



part number (from table shown), and date of re-configuration added to label (Illustration 3).



Note:



These calibration files offer two separate improvements: the shift quality improvement (Technical Bulletin S307-07) and the rectification



of the false flagging of DTC P1383 or P1388 (Technical Bulletin S303-09). If a vehicle exhibits both concerns, it is not necessary to



perform both bulletins, since both improvements will result when performing either bulletin.



7. After the reprogramming of the PCM is complete, switch "OFF" PTU, disconnect and return WDS to original location.



8. Remove fender protector covers and close hood.



2000 Jaguar S-Type (X200) V6-3.0L Page 98



9. Enter your dealer number and the date on the Authorized Modification Label as shown (Illustration 4). Write in "Reflash per TSB



S303-09/S307-07." Apply the label to the left B-post below the door striker plate. Be sure to apply the clear protective sheet over the label.



Parts Information:



To obtain blank Authorized Modification Labels, refer to Administration Bulletin 6-94 titled "Availability of Service Action and Recall Authorized



Modification Labels/stickers."



DESCRIPTION PART NUMBER QTY



Generic update JJM 998499/20 1



label



Warranty Information:



Warranty claims should be submitted quoting the information found in the table.



This will result in payment of the stated time and, where applicable parts/miscellaneous expense codes as listed.

No comments:

Post a Comment