2010 Land Rover LR4 (LA) V8-5.0L Technical Service Bulletin # TECLTB00278 Date: 100427
Body - Revised Body Removal/Installation
No.: LTB00278
Issue: 1
Date: 27 APR 2010
SECTION: 502
Revised Workshop Procedure: Body Assembly Remove / Refit
AFFECTED VEHICLE RANGE:
CONDITION SUMMARY:
Situation:
The Workshop Manual procedure for removing and refitting the body assembly has been revised. The revised procedure has several steps removed
or re-timed, including but not limited to:
^ Bumper renew (front and rear) has been replaced with bumper remove / refit for access
^ Complete coolant drain has been replaced with a coolant top up as only one (1) liter is lost
^ Shields located under the front wheel arches no longer require removal
^ Steering column repair time has been reevaluated
NOTE:
Associated repair times requiring body removal will also change.
2010 Land Rover LR4 (LA) V8-5.0L Page 147
Action:
When removing and refitting the body assembly, refer to the Repair Procedure outlined below.
PARTS:
No parts necessary; information only
TOOLS:
Refer to Workshop Manual (GTR) for any required special tools
WARRANTY:
NOTE:
Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only.
Always refer to DDW to obtain the latest repair time.
DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.
Normal warranty policy and procedures apply.
REPAIR PROCEDURE
REMOVE / REFIT BODY ASSEMBLY
NOTE:
Global Technical Reference (GTR) lookup sequence is as follows:
GTR Home > NAS > Model > Service Information > Model Year > Workshop Manual
1. Refer to Workshop Manual (GTR) section 502-02, Full Frame and Body Mounting, to remove / refit the body assembly.Technical Service
Bulletin # TECLTB00288 Date: 100717
Audio - Satellite Radio Defaults To Channel 184 From 001
NO: LTB00288
ISSUE: 1
DATE: 17 JUNE 2010
SECTION: 415
SDARS Changes From Channel 001 to 184
AFFECTED VEHICLE RANGE
2010 Land Rover LR4 (LA) V8-5.0L Page 148
CONDITION SUMMARY:
Situation:
The Satellite Digital Audio Receiving System (SDARS) may switch to channel 184 if the last listened-to channel was 001 (Hits 1) when the ignition
was switched 'OFF'. This may be caused by a software issue within the Audio front control module.
Action:
In the event of a customer concern of the above, refer to the Repair Procedure outlined below to update the Audio Front Control Module software.
PARTS:
No parts necessary
TOOLS:
IDS with latest IDS-DVD and Calibration File; first available on IDS-DVD121_V6.08 Calibration File 37 Land Rover-approved Midtronics Vehicle
Power Supply
Refer to Workshop Manual (GTR) for any required special tools
WARRANTY:
NOTE:
Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always
refer to DDW to obtain the latest repair time.
DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.
REPAIR PROCEDURE
UPDATE THE AUDIO FRONT CONTROL MODULE SOFTWARE
CAUTION:
Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these steps may cause damage to control modules in the vehicle.
CAUTION:
A Land Rover-approved Midtronics Vehicle Power Supply must be connected to the vehicle battery during IDS diagnosis / module programming.
1. Connect the Land Rover-approved Midtronics Vehicle Power Supply to the vehicle battery.
NOTE:
IDS must be loaded with IDS-DVD121_V6.08 or later and Calibration File 37 or later.
2. Connect the IDS to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.
3. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.
4. From the Session Type selection screen, choose 'Diagnosis'.
5. Select the 'Selected Symptoms' tab, and then select:
^ Electrical > Information and entertainment system > Entertainment system > Audio > Radio loses preset stations
6. Select 'continue'.
7. Select the 'Recommendations' tab.
2010 Land Rover LR4 (LA) V8-5.0L Page 149
8. From the Recommendations tab, select 'Run' to configure the 'Audio front control module'
^ Follow all on-screen instructions to complete this task.
9. Exit the current session.
10. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.
11. Close all doors, tailgate, and hood.
12. Lock the vehicle; wait 10 seconds.
13. Unlock the vehicle; wait 10 seconds.
14. Repeat steps 11 and 12.
15. Verify radio (AM / FM / CD / SDARS) operation.
No comments:
Post a Comment