Skip to main content

Mercedes Benz Truck Sprinter 2500 Crew (906.733) V6-3.0L DSL Turbo (642.898) Technical Service Bulletin # S-91_60-195A Date: 120118


Restraints - Repair And Diag. Of Airbag Wiring Harnesses



Date: January 18, 2012



Order No: S-B-91.60/195a



Supercedes: S-B-91.60/195, January 6, 2012



Group: 91



Revision a: Parts information removed. Reference EPC-net for relevant parts.



SUBJECT: MY-All, Models All



Repair and Diagnosis of Airbag Wiring Harness



When a driver airbag, front-passenger airbag, sidebag or windowbag or an emergency tensioning retractor is triggered, the coupling melts from the



gas generator heat and becomes unusable. Up until now, repair on airbag wiring harnesses was not permitted due to safety reasons and had to be



partly or completely replaced depending on type. As always follow most current part numbers and corresponding information in EPC before



ordering.



NOTE:



The part numbers for the solder connector are available in the EPC under the DG (design group) ...\54\019. The "Repairing wiring harness using



solder connectors" document is to be observed.



Follow WIS AR54.18-P-0600A Repair supplemental restraint system (SRS) squib wiring harness for Models:



Model 124, 126, 129, 140, 163, 164, 166, 168, 169, 170, 171, 172, 197, 202, 203, 204, 207, 208, 209, 210, 211, 212, 215, 216, 218, 219, 220, 221,



230, 240, 245, 246, 251, 414, 461, 463.



Follow WIS AR54.18-P-0600SLR Repair supplemental restraint system (SRS) squib wiring harness for Model: 199.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...