Skip to main content

2020 Mercedes Benz Truck ML 63 AMG Technical Service Bulletin # S-82_85-697

2020 Mercedes Benz Truck ML 63 AMG Technical Service Bulletin # S-82_85-697 Date: 110209

COMAND(R) - APS (A40/3) Telematics Generation 2.5 Info. Date: February 9, 2011 Order No.: S-B-82.85/697 Group: 82 SUBJECT: MY2009 to Present, Model 164, 171, 211, 219, 230, 251 with Code 512 COMAND APS with DVD changer, with Code 527 COMAND APS with single DVD drive (with navigation); Model 203.7 with Code 527 COMAND APS with single DVD drive (with navigation) with Code 044 New Telematics Generation NTG 2.5; Model 463 with Code (EU1) Replace Hard Disk There is now a separate replacement procedure for the COMAND APS (A40/3) telematics generation 2.5. Perform a quick test to ensure the disk is causing the problem. NOTE: DTC 94D9 - internal hard disk has a malfunction is a key DTC to look for. Page 117 Customer complaints indicative of a defective hard disk are in group 82 of TIPS. You must first use XENTRY diagnostics to ascertain a hard drive/hard disk error. After the hard disk has been installed, SCN code and program the control unit. For the guided procedure go to: COMAND APS > Initial startup > Replacement of hard disk. After installation of the hard disk, also update the navigation map with the appropriate DVD. See WIS document AR82.85-P-1001A for Remove and Install of the COMAND APS hard disk.


Labels

Labels:

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more