Y58/1 (Purge control valve) : Open circuit / Switchover valve permanently closed (P0444)

P0444
Y58/1 (Purge control valve) : Open circuit / Switchover valve permanently closed (P0444)
Possible cause:
­ Y58/1 (Purge control valve)
­ K40/4f44 (Fuse 44)
­ K40/4kK (Engine electronics and chassis relay)
Affected functions:
­
Engine diagnosis
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
Test 1: Arrangement of fuses
Test 2: Check component Y58/1 (Purge control valve).
1. Arrangement of fuses
End of test
2. Check component Y58/1 (Purge control valve).
Test 2.1: Actuate component Y58/1 (Purge control valve).
Test 2.2: Test current consumption of component Y58/1 (Purge control valve).
Test 2.3: Perform mechanical inspection of component Y58/1 (Purge control valve).
2.1. Actuate component Y58/1 (Purge control valve).
10.52SS
Page 8042010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
Page 805
Test sequence
­
­
Switch on ignition.
Actuate component Y58/1 (Purge control valve).(Operate pushbutton F2.)
Warning!Communication with ECU required.
2.2. Test current consumption of component Y58/1 (Purge control valve).
Figure legend
­ A ­ConnectionTest cable 35­pin socket box
­ 001 ­Sockets of component N3/10 (ME­SFI [ME] control unit)
­ 05 ­35­pin socket box
­ 050 ­126­pin socket box
­ 108 ­Test cable 266 589 01 63 00
­ N3/10 (ME­SFI [ME] control unit)
­ II 1­63ConnectionTest cable
­ III 64­126ConnectionTest cable
Warning!
­
­
Connection A of test cable 108 may NOT be connected to connection B of the 126­pin socket box (050).
Test prerequisite
­ Actuation is not OK.
Test sequence
­
­
­
­
Switch off ignition.
Connect socket box (126­pin) to component N3/10 (ME­SFI [ME] control unit).
Connect socket box (35­pin) to component N3/10 (ME­SFI [ME] control unit).
Measure direct current with multimeter between socket [F.4] 100 of the 126­pole socket box tester and socket [F.45] 15 of the
35­pole socket box tester.
­ Switch on ignition.
Specified value2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
­ Amperage[0.4...0.9] A
Question
­
Is the measurement value OK?
YES
The measurement value is OK.Possible cause and remedy
­ Perform mechanical inspection of component Y58/1 (Purge control valve).
End of test
NO
The measurement value is not OK.Possible cause and remedy
­ K40/4f44 (Fuse 44)
­ K40/4kM (Circuit 30z relay)
­ Line from component N3/10 (ME­SFI [ME] control unit) to component Y58/1 (Purge control valve)
­ Line from component K40/4 (Front passenger fuse and relay module) to component Y58/1 (Purge control valve)
­ Y58/1 (Purge control valve)
End of test
2.3. Perform mechanical inspection of component Y58/1 (Purge control valve).
Figure legend
­ 019Vacuum tester
­ a3­point distributor
­ bVacuum line to activated charcoal canister
­ Y58/1 (Purge control valve)
Test prerequisite
­ Actuation is OK.
Test sequence
­ Switch off ignition.
­ Connect the vacuum tester to the input of component Y58/1 (Purge control valve) with the 3 x distributor.
­ Operate engine at idling speed.
­ Engine at operating temperature
­ Actuate component Y58/1 (Purge control valve), then with key F2.
Specified value
Page 8062010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985)
Copyright ? 2013, ALLDATA
­ Component Y58/1 (Purge control valve) should pulse.
­ The value should be > 5 mbar during actuation.The pointer of the vacuum tester swings.
Proceed to 'Actuation' with F2
Warning!Communication with ECU required.