Tooth space on sensor rotor temporarily not detected or wiring error (P0335)
Tooth space on sensor rotor temporarily not detected or wiring error (P0335)
Possible cause:
B70 (Crankshaft Hall sensor)
Affected functions:
Page 7362010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
Engine diagnosis
Test 1: Check component B70 (Crankshaft Hall sensor).
1. Check component B70 (Crankshaft Hall sensor).
Test 1.1: Test signal voltage of component B70 (Crankshaft Hall sensor).
Test 1.2: Check power supply of component B70 (Crankshaft Hall sensor).
1.1. Test signal voltage of component B70 (Crankshaft Hall sensor).
Test 1.1.1: Engine running
Test 1.1.2: The engine does not start.
1.1.1. Engine running
Figure legend
A ConnectionTest cable 35pin socket box
001 Sockets of component N3/10 (MESFI [ME] control unit)
05 35pin socket box
050 126pin socket box
108 Test cable 266 589 01 63 00
N3/10 (MESFI [ME] control unit)
II 163ConnectionTest cable
III 64126ConnectionTest cable
Warning!
Connection A of test cable 108 may NOT be connected to connection B of the 126pin socket box (050).
Settings
Trigger level: 50 %
Page 7372010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
Time range: 5 ms
Test sequence
Switch off ignition.
Connect socket box (126pin) to component N3/10 (MESFI [ME] control unit).
Observe oscilloscope pattern between sockets (M.80) 80(A7) and (M.81) 81(A4) of the 126pole socket box tester.
Operate engine at idling speed.
Specified value
Measuring system
Signal (4,7 5,3) V
Warning!The rising signal edge in the gap (see arrow) may vary.Note
Measuring system:Communication with ECU required
1.1.2. The engine does not start.
Figure legend
A ConnectionTest cable 35pin socket box
001 Sockets of component N3/10 (MESFI [ME] control unit)
05 35pin socket box
050 126pin socket box
108 Test cable 266 589 01 63 00
N3/10 (MESFI [ME] control unit)
II 163ConnectionTest cable
III 64126ConnectionTest cable
Warning!
Connection A of test cable 108 may NOT be connected to connection B of the 126pin socket box (050).
Page 7382010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
Settings
Trigger level: 50 %
Time range: 5 ms
Test sequence
Switch off ignition.
Connect socket box (126pin) to component N3/10 (MESFI [ME] control unit).
Observe oscilloscope pattern between sockets (M.80) 80(A7) and (M.81) 81(A4) of the 126pole socket box tester.
Start engine.
Specified value
Measuring system
Warning!The rising signal edge in the gap (see arrow) may vary.Note
Measuring system:Communication with ECU required
Page 7392010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
1.2. Check power supply of component B70 (Crankshaft Hall sensor).
Figure legend
A ConnectionTest cable 35pin socket box
001 Sockets of component N3/10 (MESFI [ME] control unit)
05 35pin socket box
050 126pin socket box
108 Test cable 266 589 01 63 00
N3/10 (MESFI [ME] control unit)
II 163ConnectionTest cable
III 64126ConnectionTest cable
Warning!
Connection A of test cable 108 may NOT be connected to connection B of the 126pin socket box (050).
Page 7402010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
Test sequence
Switch off ignition.
Connect 126pole socket box between engine wiring harness and control module N3/10 (MESFI [ME] control unit).
Measure direct voltage with multimeter between sockets (M.80) 80 and (M.44) 44 of the 126pole socket box tester.
Switch on ignition.
Specified value
Voltage[4.8...5.3] V
Question
Is the measurement value OK?
YES
The measurement value is OK.Possible cause and remedy
Signal wire
Test cables to component B70 (Crankshaft Hall sensor) for open circuit.
B70 (Crankshaft Hall sensor)
End of test
NO
The measurement value is not OK.Possible cause and remedy
Check lines to component B70 (Crankshaft Hall sensor) for short circuit.
N3/10 (MESFI [ME] control unit)
End of test
Tooth space on sensor rotor temporarily not detected or wiring error (P0335)
Possible cause:
B70 (Crankshaft Hall sensor)
Affected functions:
Page 7362010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
Engine diagnosis
Test 1: Check component B70 (Crankshaft Hall sensor).
1. Check component B70 (Crankshaft Hall sensor).
Test 1.1: Test signal voltage of component B70 (Crankshaft Hall sensor).
Test 1.2: Check power supply of component B70 (Crankshaft Hall sensor).
1.1. Test signal voltage of component B70 (Crankshaft Hall sensor).
Test 1.1.1: Engine running
Test 1.1.2: The engine does not start.
1.1.1. Engine running
Figure legend
A ConnectionTest cable 35pin socket box
001 Sockets of component N3/10 (MESFI [ME] control unit)
05 35pin socket box
050 126pin socket box
108 Test cable 266 589 01 63 00
N3/10 (MESFI [ME] control unit)
II 163ConnectionTest cable
III 64126ConnectionTest cable
Warning!
Connection A of test cable 108 may NOT be connected to connection B of the 126pin socket box (050).
Settings
Trigger level: 50 %
Page 7372010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
Time range: 5 ms
Test sequence
Switch off ignition.
Connect socket box (126pin) to component N3/10 (MESFI [ME] control unit).
Observe oscilloscope pattern between sockets (M.80) 80(A7) and (M.81) 81(A4) of the 126pole socket box tester.
Operate engine at idling speed.
Specified value
Measuring system
Signal (4,7 5,3) V
Warning!The rising signal edge in the gap (see arrow) may vary.Note
Measuring system:Communication with ECU required
1.1.2. The engine does not start.
Figure legend
A ConnectionTest cable 35pin socket box
001 Sockets of component N3/10 (MESFI [ME] control unit)
05 35pin socket box
050 126pin socket box
108 Test cable 266 589 01 63 00
N3/10 (MESFI [ME] control unit)
II 163ConnectionTest cable
III 64126ConnectionTest cable
Warning!
Connection A of test cable 108 may NOT be connected to connection B of the 126pin socket box (050).
Page 7382010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
Settings
Trigger level: 50 %
Time range: 5 ms
Test sequence
Switch off ignition.
Connect socket box (126pin) to component N3/10 (MESFI [ME] control unit).
Observe oscilloscope pattern between sockets (M.80) 80(A7) and (M.81) 81(A4) of the 126pole socket box tester.
Start engine.
Specified value
Measuring system
Warning!The rising signal edge in the gap (see arrow) may vary.Note
Measuring system:Communication with ECU required
Page 7392010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
1.2. Check power supply of component B70 (Crankshaft Hall sensor).
Figure legend
A ConnectionTest cable 35pin socket box
001 Sockets of component N3/10 (MESFI [ME] control unit)
05 35pin socket box
050 126pin socket box
108 Test cable 266 589 01 63 00
N3/10 (MESFI [ME] control unit)
II 163ConnectionTest cable
III 64126ConnectionTest cable
Warning!
Connection A of test cable 108 may NOT be connected to connection B of the 126pin socket box (050).
Page 7402010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985)
Copyright ? 2013, ALLDATA
10.52SS
Test sequence
Switch off ignition.
Connect 126pole socket box between engine wiring harness and control module N3/10 (MESFI [ME] control unit).
Measure direct voltage with multimeter between sockets (M.80) 80 and (M.44) 44 of the 126pole socket box tester.
Switch on ignition.
Specified value
Voltage[4.8...5.3] V
Question
Is the measurement value OK?
YES
The measurement value is OK.Possible cause and remedy
Signal wire
Test cables to component B70 (Crankshaft Hall sensor) for open circuit.
B70 (Crankshaft Hall sensor)
End of test
NO
The measurement value is not OK.Possible cause and remedy
Check lines to component B70 (Crankshaft Hall sensor) for short circuit.
N3/10 (MESFI [ME] control unit)
End of test
