Skip to main content

Disclaimer2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 09-08-50-017B Date: 100211

Disclaimer2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 09-08-50-017B Date: 100211



Electrical - No Crank/No Start/Discharged or Low Battery



TECHNICAL



Bulletin No.: 09-08-50-017B



Date: February 11, 2010



Subject: No Crank, No Start, Discharged or Low Battery (Reprogram Rear Heated Seat Module)



Models:



2006-2010 Cadillac DTS



Built Prior to February 2, 2010



2007-2010 Cadillac Escalade, Escalade ESV



2007-2010 Chevrolet Suburban, Tahoe



2007-2010 GMC Yukon, Yukon XL



Built Prior to November 30, 2009



All Equipped with Rear Heated Seat RPO KA6



Supercede:



This bulletin is being revised to add build breakpoint dates. Please discard Corporate Bulletin Number 09-08-50-017A (Section 08 - Body and



Accessories).



Condition



Some customers may comment about a no crank/no start condition or a discharged or low battery.



Note



This condition may be intermittent, therefore it is important to check if a revised calibration has been released on TIS2WEB for this concern, even



if the condition cannot be duplicated at the dealer.



Cause



This condition may be caused by the rear heated seat module (RHSM) discharging the battery by keeping the serial data bus active, which creates a



cumulative continuous draw of four amps on the battery after the vehicle is shut down, until the state of charge reaches three volts.



Correction



Important



DO NOT replace the RHSM or the battery for this concern.



Reprogram the RHSM with the latest software calibration.



Important



Select the correct calibration files for the appropriate vehicle configuration (body style) and RPO codes.



A revised calibration has been developed to address this condition. Technicians are to reprogram the RHSM using the Service Programming



System (SPS) with the latest software available on TIS2WEB. Refer to the Service Programming System (SPS) procedures in SI.



When using a Tech 2(R) or a Multiple Diagnostic Interface (MDI) for reprogramming, ensure that it is updated with the latest software version.



During programming, the battery voltage must be maintained within the proper range of 12-15 volts. Only use the approved Midtronics(R) PSC 550



Battery Maintainer (SPS Programming Support Tool EL-49642) or equivalent during programming.



2010 Cadillac Truck Escalade RWD V8-6.2L Page 280



Warranty Information



For vehicles repaired under warranty, use:

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...