2010 Cadillac Truck SRX FWD V6-3.0L Page 1006

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition ON, observe the DTC information with a scan tool. Verify that none of the following DTCs are set. DTC P0010, P0013, P0020,

P0023, P0335, P0336, P0340, P0341, P0345, P0346, P0365, P0366, P0390, or P0391.

瀚慖f any of the DTCs listed are set refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for further diagnosis.

2. Idle the engine at normal operating temperature. DTCs P0016, P0017, P0018, or P0019 should not set.

瀚慖f a DTC sets, inspect for the following and repair as necessary:

* The correct installation of the camshaft sensors

* The correct installation of the crankshaft sensor

* A timing chain tensioner condition

* An incorrectly installed timing chain

* Excessive play in the timing chain

* A mechanical cam actuator that is stuck in the full advance or retard position.

* A timing chain that jumped teeth

* A crankshaft reluctor wheel that has moved in relationship to top dead center (TDC) on the crankshaft

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Timing Chain Alignment Diagram (See: Engine, Cooling and Exhaust/Engine/Timing Components/Timing Component Alignment

Marks/Locations)

* Camshaft Timing Drive Components Cleaning and Inspection (See: Engine, Cooling and Exhaust/Engine/Service and Repair/Overhaul/81.

Camshaft Timing Drive Components Cleaning and Inspection)

* Crankshaft and Bearing Cleaning and Inspection (See: Engine, Cooling and Exhaust/Engine/Service and Repair/Overhaul/66. Crankshaft

and Bearing Cleaning and Inspection)

P16F3

DTC P0601-P0604, P0606, P0607, P0610, P062B, P062F, P0630, P16F3, or P2610 (ECM, LF1/LFW/LWR)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory Performance

DTC P0602

- Control Module Not Programmed

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: A80 (Intelligent servo module for DIRECT SELECT) Affected functions: Drive position selection Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:270641Possible cause and remedy Internal fault in control unit Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**: - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**: - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**: - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**: - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...

Mercedes Benz

Search This Blog