2010 Cadillac Truck SRX FWD V6-3.0L Technical Service Bulletin # 09-04-95-001D Date: 120716

Drivetrain - Noise Shifting Between Reverse And Drive

TECHNICAL

Bulletin No.: 09-04-95-001D

Date: July 16, 2012

Subject: Clicking Type Noise from Front or Rear of Vehicle When Shifting Between Reverse and Drive or on Hard Acceleration (Add Washer to

Wheel Drive Shaft)

Models:

2010-2011 Buick LaCrosse

2011 Buick Regal

2008-2011 Cadillac CTS, CTS Wagon, Coupe (Includes V Series)

2010-2011 Cadillac SRX

2009-2011 Chevrolet HHR

2010 Chevrolet Camaro Built Prior to June 1, 2009 (V8 Engine (All) and V6 Engine (Manual)) or February 17, 2010 (V6 Engine (Automatic))

2010-2011 Chevrolet Equinox

2011 Chevrolet Cruze

2010-2011 GMC Terrain

Supercede:

This bulletin is being revised to add the HHR model. Please discard Corporate Bulletin 09-04-95-001C (Section 04 - Driveline/Axle).

Condition (Cruze, Equinox, HHR, LaCrosse, Regal, SRX, Terrain)

Some customers may comment on a clicking type noise coming from the front of the vehicle when shifting between reverse and drive or on a hard

acceleration.

Correction (Cruze, Equinox, HHR, LaCrosse, Regal, SRX, Terrain)

Add a washer between the front wheel drive shaft and the bearing hub assembly using the procedure listed below.

Note

- Some vehicles may have been built with the washer. If there is a washer already installed, remove and discard the washer. DO NOT re-use

the washer, replace with NEW only.

- Anytime the wheel drive shaft is separated from the steering knuckle, the washer must be replaced with a NEW washer only.

1. Remove the front wheel bearing and hub assembly. Refer to Front Wheel Bearing and Hub Replacement procedure in SI.

2. Install the washer (1) onto the front wheel drive shaft (2) as shown above.

Note

For Cruze, Equinox and Terrain, DO NOT reuse wheel drive shaft nut. Discard and replace with a NEW nut only.

2010 Cadillac Truck SRX FWD V6-3.0L Page 32

3. Install the front wheel bearing and hub assembly. Refer to Front Wheel Bearing and Hub Replacement procedure in SI.

4. Repeat Steps 1 through 3 for the opposite side.

Condition (CTS, Camaro)

Some customers may comment on a clicking type noise coming from the rear of the vehicle when shifting between reverse and drive or on a hard

acceleration.

Correction (CTS, Camaro)

Add a washer between the rear wheel drive shaft and the bearing hub assembly using the procedure listed below.

Note

- Some vehicles may have been built with the washer. If there is a washer already installed, remove and discard the washer. DO NOT re-use

the washer, replace with a NEW washer only.

- Anytime the wheel drive shaft is separated from the steering knuckle, the washer must be replaced with a NEW washer only.

1. Remove the rear wheel bearing and hub assembly. Refer to Rear Wheel Bearing and Hub Replacement procedure in SI.

2. Install the washer (1) onto the rear wheel drive shaft (2) as shown above.

Note

DO NOT reuse wheel drive shaft nut. Discard and replace with a NEW nut only.

3. Install the rear wheel bearing and hub assembly. Refer to Rear Wheel Bearing and Hub Replacement procedure in SI.

4. Repeat Steps 1 through 3 for the opposite side.

Parts Information

Warranty Information

2010 Cadillac Truck SRX FWD V6-3.0L Page 33

For vehicles repaired under warranty, use the table.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: A80 (Intelligent servo module for DIRECT SELECT) Affected functions: Drive position selection Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:270641Possible cause and remedy Internal fault in control unit Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**: - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**: - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**: - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**: - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...

Mercedes Benz

Search This Blog