Tuesday, May 10, 2022

2010 Cadillac Truck SRX FWD V6-3.0L Page 939

2010 Cadillac Truck SRX FWD V6-3.0L Page 939



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P06AC



- Transmission Control Module (TCM) Power Up Temperature Sensor Performance



DTC P06AD



- Transmission Control Module (TCM) Power Up Temperature Sensor Circuit Low Voltage



DTC P06AE



- Transmission Control Module (TCM) Power Up Temperature Sensor Circuit High Voltage



Circuit/System Description



The transmission control module (TCM) power up temperature sensor is located inside of the control solenoid valve assembly, which has no



serviceable components. The TCM power up temperature sensor provides the temperature of the TCM when the TCM power is on. This



temperature reading is used in various shifting and diagnostic routines and also to protect the control solenoid valve assembly and TCM. This fault



is handled inside the TCM and no external circuits are involved.



Conditions for Running the DTC



P06AC



* No DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207,



P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0658, P0668, P0669, P06AC, P06AD, P06AE,



P0712, P0713, P0716, P0717, P0722, P0723, P0962, P0963, P0966, P0967, P0970, P0971, P215C, P2720, P2721, P2729, or P2730.



* The engine speed is 400 RPM or greater for 5 seconds.



* The ignition voltage is 8.6 volts or greater.



* Brake torque is not active.



* The torque signal is valid.



* The throttle position signal is valid.



P06AD



* No DTCs P06AD, P0716, P0717, P0722, or P0723.



* The engine speed is 400 RPM or greater for 5 seconds.



* The ignition voltage is 8.6 volts or greater.



P06AE



* The engine speed is 400 RPM or greater for 5 seconds.



* The ignition voltage is 8.6 volts or greater.



* DTC P06AE has not set this ignition cycle.



Conditions for Setting the DTC



P06AC



* The difference between the transmission fluid temperature (TFT) and TCM power up temperature is greater than 20-50掳C (36-90掳F),



depending on the average of the TFT, TCM substrate, and TCM power up temperatures.



* The difference between the TCM substrate temperature and TCM power up temperature is greater than 8-10掳C (14-18掳F) depending on the



average of the TFT, TCM substrate, and TCM power up temperatures.



* The above conditions have to be met for 5 minutes within a 6 minute period.



P06AD



The TCM power up temperature is -59掳C (-74掳F) or less for 1 minute.



P06AE



The TCM power up temperature is 165掳C (329掳F) or greater for 1 minute.



Action Taken When the DTC Sets



* DTC P06AC, P06AD, P06AE are Type B DTCs.

No comments:

Post a Comment