2010 Cadillac Truck SRX FWD V6-3.0L Page 1143

2010 Cadillac Truck SRX FWD V6-3.0L Page 1143

DTC or a driveability condition. Refer to Temperature Versus Resistance - Engine Coolant Temperature Sensor (See: Powertrain

Management/Computers and Control Systems/Specifications/Temperature Versus Resistance - Engine Coolant Temperature Sensor).

* If the vehicle has sat overnight, the IAT sensor and the ECT sensor values should display within 3掳C (5掳F).

* After starting a cold engine, the ECT sensor temperature should rise steadily, then stabilize after the thermostat opens.

* High resistance in the circuits of either the ECT or IAT sensor could set a DTC.

* DTC's must be cleared before Engine Cooling Fan's are Commanded Off.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine idling for 1 min. Observe the DTC information with a scan tool. DTCs P0117 and P0118 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the B34 ECT sensor.

Caution: Do NOT use a test lamp to test the continuity of the circuit. Damage to the control module may occur due to excessive current

draw.

Note: The control module or the sensor may be damaged if the circuit is shorted to battery positive voltage.

2. Ignition Off all vehicle systems Off, this may take up to 2 minutes.Test for less than 5 ohm between the low reference circuit terminal A and

ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance, or for a short to voltage. If the circuit tests

normal, replace the K20 ECM.

3. Ignition ON, verify that the scan tool ECT sensor parameter is at -40掳C (-40掳F).

瀚慖f greater than the specified value, test the signal circuit terminal B for a short to ground. If the circuit tests normal, replace the K20 ECM.

Note: If the fuse in the jumper wire opens, the signal circuit is shorted to a voltage and the sensor may be damaged.

4. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal A and the low reference circuit terminal B. Verify the ECT

sensor parameter is greater than 142掳C (288掳F).

瀚慖f less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the K20 ECM.

5. If all circuits test normal, test or replace the B34 ECT sensor.