2010 Cadillac Truck SRX FWD V6-3.0L Page 2009

2010 Cadillac Truck SRX FWD V6-3.0L Page 2009

* The evaporative emission (EVAP) canister purge solenoid valve is not enabled.

* The fuel level is greater than 12 percent.

* The amount of air flow into the engine is greater than 7,000 grams.

* DTC P2188 run continuously once the above conditions are met.

Conditions for Setting the DTC

P2178

The Total Fuel Trim Avg. is less than -22 percent. The condition exists for 4 seconds or for a cumulative of 30 seconds.

P2188

The Total Fuel Trim Avg. is less than -40 percent. The LT FT Idle/Decel is less than -6 percent. The condition exists for 4 seconds or for a

cumulative of 30 seconds.

Action Taken When the DTC Sets

DTCs P2178 and P2188 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P2178 and P2188 are Type B DTCs.

Diagnostic Aids

* A fuel system delivery condition causes this DTC to set. Thoroughly inspect all items that cause a rich condition. Refer to Fuel System

Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System

Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel System Diagnosis (LAU China) (See: Powertrain

Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis

(LAU Except China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System

Diagnosis (Except China)).

* Review the Freeze Frame/Failure Records with a scan tool.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P2178 or P2188 should not be set.

瀚慖f there are other DTCs set besides DTC P2178 or P2188, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic

Trouble Code Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) to diagnosis the applicable DTC.

2. Ignition ON, observe the BARO pressure parameter and compare the reading on the scan tool to the barometric pressure table. Refer to