Skip to main content

Mia


最近约了Banana shop的Mia,体验分享给狼友希望有所帮助。
地点在一个townhouse里,进门上楼,路边停车很方便。

F:6.5   一般长相但是耐看,圆脸(不是网红脸那种风格),笑起来有些可爱,照片和本人没有任何关联。目测年龄 28 - 30
B:7   梨形身材,骨架小但是屁股比较大,身上有肉但没有太多赘肉,160 - 165 cm,胸有C,可惜是人工的,手感有点硬(楼主是胸奴所以这里扣掉0.5分)
S/A:8.5   MM可能在国内大场训练过,洗澡有短暂水萧,楼主躺床上后MM会开始放音乐然后在床边跳小一段舞(MM的歌单跳到了类似恭喜发财风格的歌,所以当时整个氛围其实有点跑偏。。),下来是类似国内会所流程,基本上你可以躺着不动,有胸推,没有DFK,有69,第一发是CIM(楼主之前没有试过也不太喜欢这个,但是MM当时推荐楼主试试),中间有按摩(嘴里含水舔遍全身那种),第二发CG出货。全程一直专注服务流程,中间会问你舒不舒服,不看电话
Damage: 350 / hr
总体感觉是属于服务型MM,想要GFE的狼友有可能会失望,专注享受服务的狼友可以考虑一试

第一次发帖文笔有限,各位狼友见谅!

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...