Skip to main content

Disclaimer2010 Cadillac Truck SRX AWD V6-3.0L Technical Service Bulletin # 10-08-42-001C Date: 120126

Disclaimer2010 Cadillac Truck SRX AWD V6-3.0L Technical Service Bulletin # 10-08-42-001C Date: 120126



Lighting - Low Beam Headlamp(s) Inoperative



TECHNICAL



Bulletin No.: 10-08-42-001C



Date: January 26, 2012



Subject: Low Beam Headlamp Bulb Diagnosis/Replacement (Inspect Bulb and Connector)



Models:



2008-2011 Buick Enclave



2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT



2008-2011 Cadillac CTS, CTS-V



2010-2011 Cadillac CTS Sport Wagon, SRX



2006-2011 Chevrolet Impala



2007-2011 Chevrolet Avalanche, Silverado, Suburban, Tahoe



2008-2011 Chevrolet Malibu



2009-2011 Chevrolet Traverse



2010-2011 Chevrolet Equinox



2007-2011 GMC Acadia, Sierra, Yukon, Yukon XL, Yukon Denali, Yukon Denali XL



2010-2011 GMC Terrain



2006-2010 Pontiac G6



2007-2010 Saturn AURA, OUTLOOK



Attention:



This bulletin DOES NOT apply to vehicles equipped with High Intensity Discharge (HID) lamps.



Supercede:



This bulletin is being revised to update the models to include the Chevrolet Impala. Please discard Corporate Bulletin Number 10-08-42-001B



(Section 08 - Body and Accessories).



Condition



Some customers may comment that the low beam headlamp is inoperative.



Correction



DO NOT replace the entire headlamp assembly for this condition.



Replace the bulb and inspect the connector following the procedure below.



1. Remove the headlamp bulb. Refer to Headlamp Bulb Replacement procedure in SI.



2. Inspect the connector.



- If the connector is NOT discolored or damaged, replace the bulb only. For bulb part numbers, see Headlamp Bulb (Low Beam) in Group



02.727 of the appropriate Parts Catalog.



- If the connector is discolored at the bulb interface, replace the connector (service pigtail listed below) and bulb.



Important



Use only Duraseal splice sleeves (salmon, P/N 19168446). Other splice sleeves may not protect the splice from moisture or



provide a good electrical connection. Refer to Splicing Copper Wire Using Splice Sleeves in SI for splicing procedures.



1. Cut the wires of the connector approximately 45 mm (1-3/4 in) from the connector and splice in the service pigtail connector. Ensure



that the splices are not above the connector when re-installing.



2010 Cadillac Truck SRX AWD V6-3.0L Page 80



2. Replace the bulb.



3. Verify that the headlamp is fully functional.



Parts Information



Warranty Information



For vehicles repaired under warranty, use the table.

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more