Recall - Replace Emergency Exit Window
FILE:
SERVICE: GROUP 00 OF SERVICE INFORMATION BINDER
PARTS: GROUP I OF INFORMATION - PARTS & ACCESSORIES BINDER
Campaign No. 2011010002, February 2011
TO: ALL MERCEDES-BENZ CENTERS
SUBJECT:
Model 906, Model Year 2010 - 2011
Replace Emergency Exit Window
Daimler AG (DAG), the manufacturer of Mercedes-Benz and Freightliner Sprinter vehicles, has determined that on certain vehicles equipped with
an emergency exit window the adhesive bond between the glass and the hinge on the top of the window may loosen. As a result the emergency exit
window may separate from the body. Dealers will check a production date on the window and replace the emergency exit window if necessary.
Included is a sample copy of a letter which owners of the affected vehicles will receive.
Prior to performing this Recall Campaign:
^ Please check VMI to insure the vehicle is involved and to determine if the vehicle has been previously repaired.
^ Please review the entire Recall Campaign bulletin.
Approximately 276 vehicles are involved.
2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)
Page 125
Procedure
1. Open emergency exit window (1, Figure 1):
Warning!
Window (1) may be loose at the top hinge and fall down when opened.
- Secure window (1) from falling down then pull handles (3) to upright (unlock) position.
Note:
Lead seals (2) will be destroyed when handles are pulled up.
^ Remove any lead seal (2) pieces from holes in sealing frame.
^ Open window (1, Figure 1) slightly.
2. Check if window (1, Figure 1) is loose at top hinge:
^ If window (1) is loose at top hinge when opened, proceed to step 5 (replace emergency window).
^ If window (1) is not loose at top hinge when opened, proceed to step 3 (check manufacturers date).
3. Check manufacturer date (arrow, Figure 1) on sticker (4) affixed to bottom edge of emergency exit window (1):
^ If manufacturer date is not: 15.07.2010 or 21.07.2010; proceed to step 4 (close and lock window).
^ If manufacturer date is: 15.07.2010 or 21.07.2010, proceed to step 5 (replace window).
4. Close and lock window (1, Figure 1) in reverse order:
^ Press new lead seals (2, Figure 1) into sealing frame.
Note:
Lead seals are properly installed when they are audibly locked into sealing frame.
^ Inspect sealing frame and replace if damaged; refer to WIS: AR67.30-D-2305B, step 6
5. Replace window; refer to WIS: AR67.30-D-2305B.
Note:
(Regarding above WIS instructions):
Use locally sourced suction cups for moving window.
Note:
Return window to the QEC.
2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)
Page 126
Special Tools
Primary Parts Information
2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)
Page 127
Warranty Information
2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)
Page 128
2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)
Page 129
2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)
Page 130
2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)
No comments:
Post a Comment