Skip to main content

2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898) Technical Service Bulletin # 20100090005 Date: 101001


Campaign - Repl. DEF (AdBlue(R)) System Line



FILE: SERVICE:



GROUP 00 OF SERVICE INFORMATION BINDER



PARTS: GROUP I OF INFORMATION _ PARTS & ACCESSORIES BINDER



Campaign No. 2010090005, October 2010



TO: ALL MERCEDES-BENZ CENTERS



SUBJECT:



Model 906.1, Model Year 2010



Replace Diesel Exhaust After-treatment Fluid (AdBlue) System Line



Daimler AG (DAG), the manufacturer of Freightliner and Mercedes-Benz Sprinter vehicles, has determined that the metering line at the diesel



exhaust after-treatment fluid (AdBlue) tank may leak in the area of the connector due to production quality issues at the supplier. Through capillary



action the reducing agent contained in the AdBlue tank may travel through the connector and into the wiring harness, and possibly into the AdBlue



control module. This may lead to electrical signal distortions in the diesel exhaust after-treatment system.



Daimler Vans USA, LLC (DVUSA) and Mercedes-Benz USA, LLC (MBUSA) therefore has initiated a campaign of all potentially affected vehicles



described above. The service campaign will be conducted to replace the AdBlue Exhaust After Treatment System Lines. In addition the AdBlue



wiring harness and AdBlue control module will be checked for the presence of AdBlue and if found will be replaced.



Attached is a sample copy of a letter which owners of the affected vehicles will receive.



Prior to performing this Service Campaign:



^ Please check VMI to determine if the vehicle is involved in the Campaign and if it has been previously



repaired.



^ Please review the entire Service Campaign bulletin and follow the repair procedure exactly as described.



Please note that Recall and Service Campaigns do not expire and may also be performed on a vehicle with a vehicle status indicator.



Approximately 325 vehicles are affected.



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 110



Procedure



Note:



^ For vehicles where AdBlue fluid line and connector are not accessible (vehicles body is blocking access) proceed to Subject A.



^ For vehicles with chassis only proceed to Subject B



A. Replace AdBlue Fluid Line and Check Harness (Fluid Line Connector and Harness to AdBlue Pump are Not Accessible)



Caution!



For information on preventing damage to electronic components due to electrostatic discharge; refer to:



WIS: AH54.00-P-0001-01A



1. Disconnect electrical connector at AdBlue control module (4, Figure 1) refer to WIS:



AR14.40-D-2020S steps 1-5 only.



WARNING!



Risk of burn injuries and scalding when working at AdBlue lines and the components attached to them.



Risk of injury to skin and eyes when handling AdBlue. Risk of poisoning caused by swallowing AdBlue.



Pour AdBlue into suitable containers only. Wait until the pressure is released before starting any work on the exhaust aftertreatment system; refer to



WIS document: AS14.40-Z-0001-01A.



For notes on use, material properties and handling of AdBlue; refer to WIS document:



AH14.40-N-0001-01AB.



2. Disconnect electrical connector (Arrow, Figure 1) of AdBlue line (1) to frame wiring harness (3):



^ Unclip AdBlue frame wiring harness clips (A, Figure 1) from frame.



^ Remove AdBlue fluid line mounting clip (B Figure 1) from frame stud.



^ Loosen AdBlue tank (2, Figure 1) to allow access to AdBlue frame wire harness connector (arrow) (do not remove tank); refer to WIS:



AR14.40-D-2014SA steps 1-5, 7.



^ Disconnect electrical connector (arrow, Figure 1) of AdBlue line (1) to frame wiring harness (3).



Note:



Allow a drying time of 4 hours to determine if AdBlue crystal formations appear on the electrical connectors (disconnected in steps 1 and 2).



During this time proceed to step 3 of this procedure.



3. Replace AdBlue fluid line (1, Figure 1); refer to WIS document: AR14.40-D-2001SA then continue with Procedure.



Note (regarding above WIS instructions):



^ For AdBlue line connector (C, Figure 1) removal from AdBlue pump fitting: Slightly twist /rotate the AdBlue line connector (C) on the



AdBlue pump fitting before removing (refer also to above WIS instructions for complete information). Be careful not to break the



AdBlue pump fitting



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 111



^ An AdBlue fluid line mounting clip (Arrow, Figure 2) is located above storage box (A, Figure 3) under right seat. Remove this clip by



prying it off from the mounting stud (do not remove storage box [A}).



^ Ensure that frame mounting clip (arrow, Figure 2) is transferred from old Adblue fluid line to new fluid line in the same position on the



line. The new line will have white paint marks indicating the mounting



clips location.



^ Do not remove AdBlue injection valve (A, Figure 4) from exhaust pipe. Pull back insulation (B) near end of AdBlue line and remove



retaining clip (arrow) to disconnect line. Installation is in reverse order. Be to sure roll back insulation over Adblue line when installing



new AdBlue line.



Note:



Perform service work on other vehicles during the 4 hour AdBlue drying time on the connectors.



4. Check for crystal formation on AdBlue control module (4, Figure 1) connectors after 4 hours of drying time:



^ If crystal formation can be seen on connectors (4, Figure 1):



Replace AdBlue control module (4); refer to WIS document: AR14.40-D-2020S then proceed to step 5.



Note:



Anticipated replacement rate for control module replacement is very low; ensure replacement criteria is met.



^ If no crystal formation can be seen on connectors (4, Figure 1):



Proceed to Step 5.



5. Check for crystal formation on electrical connectors of AdBlue line (1, Figure 1) to frame wiring harness (3):



^ If crystal formation can be seen on electrical connectors:



Replace frame wiring harness (3) then continue with procedure.



Note:



Anticipated replacement rate for frame wiring harness replacement is very low; ensure replacement criteria is met.



^ If no crystal formation can be seen on electrical connectors:



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 112



Continue with Procedure.



6. Reassemble in reverse order. Top-off AdBlue tank.



7. Perform SCN coding of in instrument cluster, refer to WIS: AR54.21-P-0013-02X



8. Read out fault memory; refer to WIS document: AD00.00-D-2000-04SD.



B. Replace AdBlue Fluid Line, Check Harness on Chassis



Caution!



For information on preventing damage to electronic components due to electrostatic discharge; refer to:



WIS: AH54.00-P-0001-01A



1. Disconnect electrical connector at AdBlue control module (4, Figure 5) refer to WIS:



AR14.40-D-2020S steps 1-5 only.



2. Disconnect electrical connector (arrow, Figure 5) of AdBlue line (1) to frame wiring harness (3).



Note:



Drying time of 4 hours must be allowed to determine if AdBlue crystal formations appear on the electrical connectors (disconnected in steps 1



and 2). During this time proceed to step 3 of this procedure.



WARNING!



Risk of burn injuries and scalding when working at AdBlue lines and the components attached to them.



Risk of injury to skin and eyes when handling AdBlue. Risk of poisoning caused by swallowing AdBlue.



Pour AdBlue into suitable containers only. Wait until the pressure is released before starting any work on the exhaust aftertreatment system.



Refer to WIS document: AS14.40-Z-0001-01A.



Note:



For notes on use, material properties and handling of AdBlue; refer to WIS document:



AH14.40-N-0001-01AB.



3. Replace AdBlue fluid line (1, Figure 5); refer to WIS document: AR14.40-D-2001SA then continue with Procedure.



Note (regarding WIS AR14.40-D-2001SA):



^ For Adblue line connector (A, Figure 5) removal from AdBlue pump fitting: Slightly twist /rotate the AdBlue line connector (A) on the



AdBlue pump fitting before removing (refer also to above WIS instructions for complete information). Be careful not to break the AdBlue



pump fitting.



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 113



^ An AdBlue fluid line mounting clip (arrow, Figure 6) is located above storage box (A, Figure 7) below right seat. Remove this clip by prying



it off from the mounting stud (do not remove storage box [A]).



^ Ensure that frame mounting clip (arrow, Figure 6) is transferred from old Adblue fluid line to new fluid line in the same position on the line.



The new line will have white paint marks indicating the mounting clips location.



^ Do not remove AdBlue injection valve (A, Figure 8) from exhaust pipe. Pull back insulation (B) near end of AdBlue line and remove



retaining clip (arrow) to disconnect line. Installation is in reverse order. Be sure to roll back insulation over Adblue line when installing new



AdBlue line.



Note:



Perform service work on other vehicles during the 4 hour AdBlue drying time on the connectors.



4. Check for crystal formation on AdBlue control module (4, Figure 5) connectors after 4 hours of drying time:



^ If crystal formation can be seen on connectors (4, Figure 5):



Replace AdBlue control module (4); refer to WIS document: AR14.40-D-2020S then proceed to step 5.



Note:



Anticipated replacement rate for control module is very low; ensure replacement criteria is met.



^ If no crystal formation can be seen on connectors (4, Figure 5):



Proceed to Step 5.



5. Check for crystal formation on electrical connectors of AdBlue line (1, Figure 5) to frame wiring harness (3):



^ If crystal formation can be seen on electrical connectors:



Replace frame wiring harness (3) then continue with procedure.



Note:



Anticipated replacement rate for frame wiring harness is very low; ensure replacement criteria is met.



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 114



^ If no crystal formation can be seen on electrical connectors:



Continue with Procedure.



6. Reassemble in reverse order. Top-off AdBlue tank.



7. Perform SCN coding of in instrument cluster, refer to WIS: AR54.21-P-0013-02X



8. Read out fault memory; refer to WIS document: AD00.00-D-2000-04SD.



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 115



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 116



Primary Parts Information



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 117



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 118



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 119



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)

Comments

Popular posts from this blog

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948) A L L Diagnostic Trouble Codes ( DTC ): P Code Charts P1240

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948)     A L L  Diagnostic Trouble Codes ( DTC ): P Code Charts P1240 The CAN bus is malfunctioning.   Test 1: Check the CAN communication with control unit Engine control module.   Test 2: Possible cause: - Drive train CAN bus Affected functions: - Engine diagnosis - Fuel system 1. Check the CAN communication with control unit Engine control module. Important note A CAN timeout fault code is set due to the absence of a CAN input signal.The cause of this may be not only the transmitter control unit, but also the CAN networking.Possible cause and remedy - Check CAN communication with affected control unit. - Check other control units for vehicle CAN bus failure in the stored faults. - CAN bus has loose contact or Open circuit. Continue with button F 2 Warning!Communication with ECU required. 2. No further information available.

2019 Mercedes-Benz X-Class

Launched for the brand new 3-Series coupe and convertible and provided on all engine variants, M Sport cars include a raft of extra equipment as standard compared to an SE model. Furthermore, passive safety is offered thanks to standard tools akin to seven airbags and the i-Size attachment system for 2 little one seats. Standard safety gear includes antilock disc brakes, stability and traction management, aspect airbags, side curtain airbags, knee airbags and Mercedes-Benz's "mbrace" emergency telematics system. The SLS is supposed to be Mercedes-Benz's ultimate vehicle, however it is also meant to be extra affordable and sensible to drive than the now-discontinued Mercedes SLR McLaren. Twelve (more than one-third) of the above differences are in the double digits. Although the price is affordable or not, are the primary disadvantages of space and rear seats for Mercedes-Benz C-Class 220 CDI vibration motor in the city. In case your body kit includes entrance and/or r...

Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601 30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input

 Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601   30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input Topic number LI80.57-P-051521 Version 1 Design group 80.57 Drive authorization systems (DAS) Date 06-01-2011 Validity All 204, 207 model vehicles Reason for change Complaint 1. No crank / no start / intermittent no crank 2. Communication via SDS to Electronic Ignition Switch N73 (EIS/EZS), and or short test may or may not be possible at time of fault 3. Below scenario: ^ When accessing the occupants compartment, the message center in the ICM will illuminate (note: eventually the message center will time out and shut down, and will not illuminate until the CAN is activated via the interior lock/unlock switch). ^ The key will turn in EIS N73. ^ The ESL N26/5 does not activate/respond (or the steering wheel remains unlocked at all times). ^ The warning icons in the ICM will not il...

2010 Mercedes Benz C 300 (204.054) V6-3.0L (272.947) Page 2499

2.1.3.2.1.4. Check power supply at control unit N15/3 (ETC [EGS] control unit). Test 2.1.3.2.1.4.1: Guided test 2.1.3.2.1.4.1. Guided test Operation number of operation texts and work units or standard texts and flat rates:27-0641Possible cause - Battery has incorrect charge state or is faulty. - Local undervoltage of component N15/3 (ETC [EGS] control unit) Test sequence - Erase fault memory. Continue with button "F2" Warning!Communication with ECU required. 2.1.3.2.1.5. Check power supply at control unit N15/5 (Electronic selector lever module control unit). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test sequence - Switch off ignition. - Disconnect connector at component N15/5 (Electronic selector lever module control unit). - Switch on ignition. - [A.2] Measure direct voltage with multimeter between 2 and 1 [A.1] Status of relevant actual value: - Supply voltage (tml. 15):Warning! Communication with ECU required. Specified ...

2010 Cadillac Truck SRX AWD V6-3.0L Page 1240

2010 Cadillac Truck SRX AWD V6-3.0L Page 1240 Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)). * Missing, restricted, or leaking exhaust components-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and Exhaust/Exhaust System/Testing and Inspection/Symptoms - Engine Exhaust). * Malfunctioning fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection). * Vacuum hoses for splits, kinks, and improper connections * Insufficient fuel in the tank * Low fuel pressure-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Test...

Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus

Part 1 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus. Possible cause: Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus Affected functions: CAN Communication Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit N80 (Steering column module). Test 3: Interior CAN check Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage How do I quickly reach my goal? How do I quickly reach my goal?First call up menu item 'Evaluation of CAN...

Relay 'Circuit 87' ( Engine ) (P2505)

P2505 Relay 'Circuit 87' ( Engine ) (P2505) Possible cause: ­ N3/10 (ME­SFI [ME] control unit) ­ K40/4kK (Engine electronics and chassis relay) Affected functions: ­ Battery / On­board electrical system ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Check power supply of component N3/10 (ME­SFI [ME] control unit). Test 2: Arrangement of fuses Page 2562010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 257 1. Check power supply of component N3/10 (ME­SFI [ME] control unit). Test 1.1: Test voltage supply of circuit 87. 1.1. Test voltage supply of circuit 87. Figure legend ­ A ­ConnectionTest cable 35­pin socket box ­ 001 ­Sockets of component N3/10 (ME­SFI [ME] control unit) ­ 05 ­35­pin socket box ­ 050 ­126­pin socket box ­ 108 ­Test cable 266 589 01 63 00 ­ N3/10 (ME­SFI [ME] control unit) ­ II 1­63ConnectionTest cable ­ III 64­126ConnectionTest cable Warning! ­ ­ Connection A of test ca...

A/T - ECO Start/Stop Inoperative, DTC P0944 Stored In TCM ECO start/stop inoperative, fault code P0944 in transmission control unit

Mercedes-Benz Mercedes Benz OEM Parts Mercedes Benz OE Replacement Parts Technical Service Bulletin # LI27-57_P-0534962 Date: 120522 2010 Mercedes Benz SL 550 (230.471) V8-5.5L (273.965)   Page 29 A/T - ECO Start/Stop Inoperative, DTC P0944 Stored In TCM ECO start/stop inoperative, fault code P0944 in transmission control unit Topic number LI27.57-P-053496 Version 2 Design group 27.57 Oil pump Date 05-22-2012 Validity NAG2 FEPlus (722.9) with auxiliary oil pump with code B03 up to transmission sequence number 7.248.200 Reason for change Model series 251 deleted because model series 251 does not have ECO start/stop. Complaint: ECO start/stop inoperative, fault code P0944 in transmission control unit. Attachments Cause: Check valve in torque converter housing may be damaged. Leakage between torque converter housing and auxiliary oil pump. May affect transmissions with transmission sequence numbers starting with -07-xxx xxx. Remedy: Access v...

Mercedes Benz SLK 55 AMG No CAN message was received from control unit Engine management.

2010 Mercedes Benz SLK 55 AMG (171.473) V8-5.5L (113.989) Copyright ? 2013, ALLDATA 10.52SS Page 1 A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Part 1 No CAN message was received from control unit Engine management. Possible cause: - Fault in CAN communication with control unit Motor electronics. - Drive train CAN bus Affected functions: - CAN Communication - Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit Engine management. Test 3: Drive train CAN test 1. Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options 1.1. Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage 1.1.1. How do I quickly reach...