2010 Cadillac Truck SRX FWD V6-3.0L Page 1386

2010 Cadillac Truck SRX FWD V6-3.0L Page 1386

- An unbalanced drive shaft

- Certain rough road conditions

- Transmission operation

- A damaged accessory drive component or belt; remove the belt and safely operate the engine to evaluate

* High resistance in the circuits of the injectors may set a misfire DTC without setting an injector DTC. Test the injector circuits of the affected

cylinder(s) for a high resistance if you suspect a condition.

* If the condition is intermittent, observing the scan tool IC Circuit Test and Fuel Injector Circuit Test Status parameters may help isolate the

condition. The circuit test status parameters will change from OK or Not Run to Fault if a condition exists.

* A condition in the heated O2 sensor (HO2S) heater control circuits may set a DTC P0300.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

* J 26792 - Spark Tester

* For equivalent regional tools, refer to Special Tools (See: Powertrain Management/Computers and Control Systems/Tools and Equipment).

Circuit/System Verification

1. Engine idling at the normal operating temperature, there should be no abnormal engine noise.

瀚慖f there is an abnormal engine noise, refer to Symptoms - Engine Mechanical (See: Engine, Cooling and Exhaust/Engine/Testing and

Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).

2. Verify that no other DTCs are set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

3. Observe the scan tool Misfire Current Cyl. 1-6 parameters. The Misfire Current Counters should not be incriminating.

4. Engine idling, perform the cylinder power balance test with a scan tool to isolate the misfiring cylinder. The engine speed should change

when each injector is disabled.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Verify that the following conditions do not exist:

* Vacuum hose splits, kinks, and incorrect connections

* Engine vacuum leaks

* Crankcase ventilation system for vacuum leaks

* Fuel pressure that is too low or too high-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and

Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:

Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel