Skip to main content

2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898) Technical Service Bulletin # LI72-16_N-048763 Date: 100201


Body - Load Compartment Sliding Door Arrester Inoperative



Load compartment sliding door arrester inoperative



Topic number LI72.16-N-048763



Version 1



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898) Page 54



Design group 72.16 Sliding doors



Date 02-01-2010



Validity 906.6## - 906.7##



Reason for change



Reason for block



Complaint:



When open, the load compartment sliding door does not lock in the end position.



Cause:



The position of the arrester at the bottom of the C-pillar prevents it from engaging in the lower sliding carriage of the load compartment sliding door.



The lower sliding carriage does not engage in the arrester.



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 55



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)



Page 56



Remedy:



Loosen the arrester and fit two washers at the upper threaded connection (only) between the bodywork and the arrester (see attachment). The bolts



must be tightened to a torque of 13 Nm.



Preparatory work: Remove step as described in WIS AR 72.16-D-7816A.



Do not replace any parts.



2010 Mercedes Benz Truck Sprinter 3500 Cab (906.153) V6-3.0L DSL Turbo (642.898)

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...