2010 Cadillac Truck SRX FWD V6-3.0L Technical Service Bulletin # 05-09-40-002F Date: 111024

2010 Cadillac Truck SRX FWD V6-3.0L Technical Service Bulletin # 05-09-40-002F Date: 111024

Restraint System - Normal Safety Belt Locking Conditions

INFORMATION

Bulletin No.: 05-09-40-002F

Date: October 24, 2011

Subject: Safety Belt Locking Conditions (Normal Operating Characteristic)

Models:

2005-2012 GM Passenger Cars and Light Duty Trucks

Supercede:

This bulletin is being revised to add the 2012 model year. Please discard Corporate Bulletin Number 05-09-40-002E (Section 09 - Restraints).

The purpose of this bulletin is to explain when the safety belts are supposed to lock. There are several different locking situations for both front and

rear safety belts.

Overspool Lock

There is an unintentional locking condition that ALL safety belts from ALL manufacturers may experience called "overspool lock". If the webbing

snaps back to the stowed position rapidly enough, the retractor will lock with the belt fully stowed. This is more likely to occur when customers

"help" the belt to retract. Without the weight of the latch plate and friction to slow the retractive speed of the webbing, the higher than normal

webbing retraction speed that occurs engages the locking mechanism when a sudden stop occurs at the end of web travel. Since the webbing is now

fully loaded on the spool, the retractor cannot rewind itself further to release the locking mechanism. When this happens, the occupant cannot

extract the belt to wear it. DO NOT replace the retractor for this condition until first attempting to disengage the locking mechanism by

following the recommendation listed below.

Recommendation

Pull hard on the locked webbing and then release. The hard pull extracts a small amount of webbing from the retractor which, in turn, permits a

small amount of retraction to occur when released. This is all that is needed to disengage the locking mechanism. The safety belt will now function

properly.

Vehicle Sensing

This type of locking occurs in response to the vehicle under the following conditions:

- The vehicle changes speed or direction abruptly (the vehicle goes into rapid acceleration OR rapid deceleration or there is aggressive

cornering).

- It can also occur in a static condition when a vehicle is parked on a large slant (fore-aft or side-to-side), such as streets in San Francisco,

California.

2010 Cadillac Truck SRX FWD V6-3.0L Page 116

- It may also occur over rough road conditions where the retractor mechanism is bounced into a locked condition.

In all of these conditions, as long as tension is maintained on the webbing, the belt will stay locked. When the tension is released, the belt retracts

slightly, the lock bar disengages and the safety belt should return to normal function. Please inform customers that may comment that "the belt

locks intermittently" that this is the design intent and the belt is functioning properly.

Web Sensing

This type of locking occurs in response to the extraction of webbing. When the webbing reels out at an accelerated rate, it goes into lock mode and

stays there until tension is again released. To observe this condition, extract the webbing quickly. Customers may refer to this condition as

"intermittent lock-up" and encounter it when trying to put the belt on too quickly.

Automatic Locking (ALR)

When the webbing is pulled all the way out, it automatically converts the retractor into a cinch-down mode (i.e. ALR). This is typically used to

tightly secure a child seat to the vehicle. Some customers may experience inadvertent activation of ALR mode if they happen to pull the belt all the

way out to the end of travel while they are putting the belt on. The ALR mode of operation is automatically cancelled when the belt is unfastened

and stowed (the belt returns to normal sensitive function).

Corvette only- This locking mechanism is also provided at the driver's position of the Corvette only, as a unique feature. Corvette customers may

find this feature appealing when they plan to operate the vehicle in a "spirited" manner (such as driving in mountainous terrain). With the ALR

active, the operator is snugly cinched into the seat and kept firmly in place during high G-force driving maneuvers.