2010 Cadillac Truck SRX FWD V6-3.0L Page 107

瀚慖f greater than the specified range, test both control circuits terminals for an open/high resistance. If the circuits test normal, replace the

K36 SDM.

7. If all circuits test normal, replace the F105, F106 air bag or F112 seat belt retractor pretensioner.

DTC B0019-B0020

1. Ignition OFF, disconnect harness connector X206.

2. Disconnect the scan tool.

3. Wait 120 seconds, test for greater than 25 ohm between the control circuit terminals listed below on the SDM side of the connector:

* F105 Passenger instrument panel air bag stage 1 X206 terminal 1 and 2

* F105 Passenger instrument panel air bag stage 2 X206 terminal 4 and 5

瀚慖f less than the specified range, test for a short between the control circuits, check each connector and CPA to ensure that the shorting

bars are lifted. If the circuits and shorting bars tests normal, replace the K36 SDM.

4. Ignition ON, test for less than 11 V between the control circuit terminals listed below and ground:

* X206 control circuit terminal 1

* X206 control circuit terminal 2

* X206 control circuit terminal 4

* X206 control circuit terminal 5

瀚慖f greater than the specified range, test the control circuit for a short to voltage. If the circuit tests normal, replace the K36 SDM.

5. Ignition OFF, test for greater than 25 ohm between the control circuit terminals listed below and ground:

* X206 control circuit terminal 1

* X206 control circuit terminal 2

* X206 control circuit terminal 4

* X206 control circuit terminal 5

瀚慖f less than the specified range, test the control circuit for a short to ground. If the circuit tests normal, replace the K36 SDM.

6. Install a 3 A fused jumper wire between the control circuit terminals listed below:

* F105 Passenger instrument panel air bag stage 1 X206 terminal 1 and 2

* F105 Passenger instrument panel air bag stage 2 X206 terminal 4 and 5

7. Verify the scan tool Deployment Loop Resistance parameter is less than 2 ohm.

瀚慖f greater than the specified range, test both control circuits terminals for an open/high resistance. If the circuits test normal, replace the

K36 SDM.

8. If all circuits test normal, replace the F105 passenger instrument panel air bag.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Driver or Passenger Seat Side Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air

Bag/Service and Repair/Removal and Replacement/Driver or Passenger Seat Side Inflatable Restraint Module Replacement)

* Seat Belt Retractor Pretensioner Replacement - Front (See: Restraints and Safety Systems/Seat Belt Systems/Seat Belt Tensioner/Service

and Repair/Removal and Replacement/Seat Belt Retractor Pretensioner Replacement - Front)

* Instrument Panel Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and

Repair/Removal and Replacement/Instrument Panel Inflatable Restraint Module Replacement)

* Roof Side Rail Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and

Repair/Removal and Replacement/Roof Side Rail Inflatable Restraint Module Replacement)

* SIR/SRS Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/SIR/SRS Wiring Repairs)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for SDM replacement, setup, and programming

B0020

DTC B0014-B0045

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: A80 (Intelligent servo module for DIRECT SELECT) Affected functions: Drive position selection Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:270641Possible cause and remedy Internal fault in control unit Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**: - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**: - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**: - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**: - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...

Mercedes Benz

Search This Blog