Saturday, October 16, 2021

2010 Cadillac Truck SRX AWD V6-3.0L Page 2147

2010 Cadillac Truck SRX AWD V6-3.0L Page 2147



* The TCM inhibits manual shifting of forward gears.



* The TCM limits the transmission to reverse and 5th gear.



* The TCM commands the high side driver OFF.



Conditions for Clearing the DIC/DTC



* DTC P2762 is a Type C DTC.



* DTCs P2763 and P2764 are Type A DTCs.



Reference Information



Connector End View Reference



* Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



* Inline Harness Connector End Views (See: Diagrams/Connector Views/Multiple Junction Connector/Connector End Views By Number)



Description and Operation



Transmission General Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and Operation/6T70/6T75 -



Automatic Transmission/Transmission General Description)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Special Tools



DT-47825-20 Adapter Harness



Circuit/System Verification



1. Operate the vehicle in second gear long enough to ensure at least a 3掳C (5掳F) rise in TCM temperature.



2. Operate the vehicle in drive range and ensure TCC is commanded ON for 1 minute. Verify with a scan tool the following test status



parameters display OK:



* TCC PC Sol. Perf. Test Status



* TCC PC Sol. Ctrl. Ckt. High Voltage Test Status



* TCC PC Sol. Ctrl. Ckt. Low Voltage Test Status



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



Note: You must perform the Circuit/System Verification first.



1. Ignition OFF, remove the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly



Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and



Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).



2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Control



Solenoid Valve and Transmission Control Module Assembly Inspection).



3. Place the control solenoid valve assembly on a clean work surface near the transmission assembly.



4. Connect the DT-47825-20 adapter harness between the vehicle wire harness electrical connector, and the control solenoid valve assembly



electrical connector.



5. Ignition ON, verify with a scan tool the following test status parameters display OK:



* TCC PC Sol. Perf. Test Status

No comments:

Post a Comment