Skip to main content

2010 Cadillac Truck SRX AWD V6-3.0L Technical Service Bulletin # 10-03-08-001B Date: 111102

2010 Cadillac Truck SRX AWD V6-3.0L Technical Service Bulletin # 10-03-08-001B Date: 111102



Suspension - Noise Over Bumps in Cold Weather



TECHNICAL



Bulletin No.: 10-03-08-001B



Date: November 02, 2011



Subject: Front Suspension Noise Over Bumps in Cold Weather (Install Revised Front Stabilizer Shaft Insulators)



Models:



2010-2011 Cadillac SRX



Supercede:



This bulletin is being revised to add VIN Breakpoints information. Please discard Corporate Bulletin Number 10-03-08-001A (Section 03 -



Suspension).



Note



Vehicles produced after the VIN breakpoints listed above will have a revised stabilizer bar design with the bushing bonded to the stabilizer bar.



Please do not attempt to remove the bonded bushing to install new bushings.



Condition



Some customers may comment on a squeak, crunch, grunt or clunk noise coming from the front of the vehicle during suspension movement over



bumps. This condition is most noticeable after the vehicle soaks in temperatures below 0掳C (32掳F). After the vehicle warms up, the noise goes



away.



Cause



This condition may be caused by the interface between the front stabilizer shaft and the front stabilizer shaft insulators (bushings).



Correction



2010 Cadillac Truck SRX AWD V6-3.0L Page 112



Remove the left and right front stabilizer insulators (bushings). Refer to Stabilizer Shaft Insulator Replacement in SI. Wipe off the surface of the



stabilizer bar to remove any loose rubber or grease residue. Install the revised left and right stabilizer insulators (bushings). For installation



instructions, refer to Stabilizer Shaft Insulator Replacement in SI. Install the new service stabilizer insulators (bushings) so that the chamfer edge is



facing toward the outside of the vehicle. This will put the slits in the bushing facing opposite directions.



Parts Information



Warranty Information



For vehicles repaired under warranty, use:

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more