Sunday, August 8, 2021

2010 Cadillac Truck SRX AWD V6-3.0L Page 1852

2010 Cadillac Truck SRX AWD V6-3.0L Page 1852



* Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



* Inline Harness Connector End Views (See: Diagrams/Connector Views/Multiple Junction Connector/Connector End Views By Number)



Description and Operation



Transmission General Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and Operation/6T70/6T75 -



Automatic Transmission/Transmission General Description)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Special Tools



DT-47825-20 Adapter Harness



Circuit/System Verification



1. Operate the vehicle in 3rd gear long enough to ensure at least a 3掳C (5掳F) rise in TCM temperature.



2. Place the gear selector in Reverse for 5 seconds and then idle the vehicle in Park for 5 seconds. Verify with a scan tool the following test



status parameters display OK:



* Shift Sol. 2 Ctrl. Ckt. High Voltage Test Status



* Shift Sol. 2 Ctrl. Ckt. Open Test Status



* Shift Sol. 2 Ctrl. Ckt. Low Voltage Test Status



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



Note: You must perform the Circuit/System Verification first.



1. Ignition OFF, remove the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly



Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and



Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).



2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Control



Solenoid Valve and Transmission Control Module Assembly Inspection).



3. Place the control solenoid valve assembly on a clean work surface near the transmission assembly.



4. Connect DT-47825-20 - jumper harness between the vehicle wire harness electrical connector, and the control solenoid valve assembly



electrical connector.



5. Ignition ON, verify with a scan tool the following test status parameters display OK:



* Shift Sol. 2 Ctrl. Ckt. High Voltage Test Status



* Shift Sol. 2 Ctrl. Ckt. Open Test Status



* Shift Sol. 2 Ctrl. Ckt. Low Voltage Test Status



瀚慖f any test status parameter displays Fault or Malfunction, replace the control solenoid valve assembly.



Repair Instructions



Important:



* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and



Inspection/Programming and Relearning) following all transmission related repairs.

No comments:

Post a Comment