2010 Cadillac Truck SRX FWD V6-3.0L Page 80

2010 Cadillac Truck SRX FWD V6-3.0L Page 80

瀚慖f greater than the specified range, test both control circuits terminals for an open/high resistance. If the circuits test normal, replace the

K36 SDM.

7. If all circuits test normal, replace the F105, F106 air bag or F112 seat belt retractor pretensioner.

DTC B0019-B0020

1. Ignition OFF, disconnect harness connector X206.

2. Disconnect the scan tool.

3. Wait 120 seconds, test for greater than 25 ohm between the control circuit terminals listed below on the SDM side of the connector:

* F105 Passenger instrument panel air bag stage 1 X206 terminal 1 and 2

* F105 Passenger instrument panel air bag stage 2 X206 terminal 4 and 5

瀚慖f less than the specified range, test for a short between the control circuits, check each connector and CPA to ensure that the shorting

bars are lifted. If the circuits and shorting bars tests normal, replace the K36 SDM.

4. Ignition ON, test for less than 11 V between the control circuit terminals listed below and ground:

* X206 control circuit terminal 1

* X206 control circuit terminal 2

* X206 control circuit terminal 4

* X206 control circuit terminal 5

瀚慖f greater than the specified range, test the control circuit for a short to voltage. If the circuit tests normal, replace the K36 SDM.

5. Ignition OFF, test for greater than 25 ohm between the control circuit terminals listed below and ground:

* X206 control circuit terminal 1

* X206 control circuit terminal 2

* X206 control circuit terminal 4

* X206 control circuit terminal 5

瀚慖f less than the specified range, test the control circuit for a short to ground. If the circuit tests normal, replace the K36 SDM.

6. Install a 3 A fused jumper wire between the control circuit terminals listed below:

* F105 Passenger instrument panel air bag stage 1 X206 terminal 1 and 2

* F105 Passenger instrument panel air bag stage 2 X206 terminal 4 and 5

7. Verify the scan tool Deployment Loop Resistance parameter is less than 2 ohm.

瀚慖f greater than the specified range, test both control circuits terminals for an open/high resistance. If the circuits test normal, replace the

K36 SDM.

8. If all circuits test normal, replace the F105 passenger instrument panel air bag.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Driver or Passenger Seat Side Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air

Bag/Service and Repair/Removal and Replacement/Driver or Passenger Seat Side Inflatable Restraint Module Replacement)

* Seat Belt Retractor Pretensioner Replacement - Front (See: Restraints and Safety Systems/Seat Belt Systems/Seat Belt Tensioner/Service

and Repair/Removal and Replacement/Seat Belt Retractor Pretensioner Replacement - Front)

* Instrument Panel Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and

Repair/Removal and Replacement/Instrument Panel Inflatable Restraint Module Replacement)

* Roof Side Rail Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and

Repair/Removal and Replacement/Roof Side Rail Inflatable Restraint Module Replacement)

* SIR/SRS Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/SIR/SRS Wiring Repairs)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for SDM replacement, setup, and programming

B0016

DTC B0014-B0045

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System