Skip to main content

2010 Cadillac Truck SRX AWD V6-3.0L Technical Service Bulletin # 08-07-30-035B Date: 101101

2010 Cadillac Truck SRX AWD V6-3.0L Technical Service Bulletin # 08-07-30-035B Date: 101101



A/T - Water Or Coolant Contamination Information



INFORMATION



Bulletin No.: 08-07-30-035B



Date: November 01, 2010



Subject: Information on Water or Ethylene Glycol in Transmission Fluid



Models:



2011 and Prior GM Passenger Cars and Light Duty Trucks



with Automatic Transmission



Supercede:



This bulletin is being revised to update model years. Please discard Corporate Bulletin Number 08-07-30-035A (Section 07 -



Transmission/Transaxle).



Water or ethylene glycol in automatic transmission fluid (ATF) is harmful to internal transmission components and will have a negative effect on



reliability and durability of these parts. Water or ethylene glycol in ATF will also change the friction of the clutches, frequently resulting in shudder



during engagement or gear changes, especially during torque converter clutch engagement.



Indications of water in the ATF may include:



- ATF blowing out of the transmission vent tube.



- ATF may appear cloudy or, in cases of extreme contamination, have the appearance of a strawberry milkshake.



- Visible water in the oil pan.



- A milky white substance inside the pan area.



- Spacer plate gaskets that appear to be glued to the valve body face or case.



- Spacer plate gaskets that appear to be swollen or wrinkled in areas where they are not compressed.



- Rust on internal transmission iron/steel components.



If water in the ATF has been found and the source of the water entry has not been identified, or if a leaking in-radiator transmission oil cooler is



suspected (with no evidence of cross-contamination in the coolant recovery reservoir), a simple and quick test kit is available that detects the



presence of ethylene glycol in ATF. The "Gly-Tek" test kit, available from the Nelco Company, should be obtained and the ATF tested to make an



accurate decision on the need for radiator replacement. This can help to prevent customer comebacks if the in-radiator transmission oil cooler is



leaking and reduce repair expenses by avoiding radiator replacement if the cooler is not leaking. These test kits can be obtained from:



Nelco Company



Test kits can be ordered by phone or through the website listed above. Orders are shipped standard delivery time but can be shipped on a next day



delivery basis for an extra charge. One test kit will complete 10 individual fluid sample tests. For vehicles repaired under warranty, the cost of the



complete test kit plus shipping charges should be divided by 10 and submitted on the warranty claim as a net item.



The transmission should be repaired or replaced based on the normal cost comparison procedure.



Important



If water or coolant is found in the transmission, the following components MUST be replaced.



- Replace all of the rubber-type seals.



- Replace all of the composition-faced clutch plates and/or bands.



- Replace all of the nylon parts.



- Replace the torque converter.



- Thoroughly clean and rebuild the transmission, using new gaskets and oil filter.



Important



The following steps must be completed when repairing or replacing.



- Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30-052F- Automatic



2010 Cadillac Truck SRX AWD V6-3.0L Page 245



Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow.



- Thoroughly inspect the engine cooling system and hoses and clean/repair as necessary.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...