2010 Cadillac Truck SRX AWD V6-3.0L Page 1717

P0741

* DTC P0741 is a Type B DTC.

* Deviation between Engine speed and output speed is less than 30 RPM during lockup control is turned on.

* DTC P0742 is a Type B DTC.

* Deviation between Engine speed and output speed is more than 100 RPM during lockup control is turned off.

Diagnostic Aids

Ensure the transmission fluid level, color and odor is correct and there are no leaks. If there are any other transmission DTCs set, diagnose those

first.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams/Electrical

Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Description and Operation

Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and

Operation/AF40-6 - Automatic Transmission/Transmission Component and System Description)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Operate the vehicle in drive with the calculated throttle position greater than 8% and ensure TCC is commanded ON and OFF a minimum of 5

times.

Verify the DTC does not reset. If the DTC resets and no other DTC is set, go to Circuit/System Testing.

If any other DTC is set, diagnose that DTC first.

Circuit/System Testing

Dynamic Test

1. Perform the line pressure check. Refer to Line Pressure Check (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Symptom Related Diagnostic Procedures/AF40-6 - Automatic Transmission/Line Pressure

Check).

2. Perform the transmission fluid check. Refer to Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Symptom Related Diagnostic Procedures/AF40-6 - Automatic Transmission/Transmission

Fluid Level and Condition Check).

3. If all circuits test normal, replace the K71 Transmission Control Module. Verify the DTC does not reset.

瀚慖f the DTC resets, go to Component Testing.

Component Testing

Static Test

1. Inspect the valve body assembly for a stuck valve, debris, or damage.

瀚慖f a stuck open or closed valve is found, replace the valve body assembly.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: A80 (Intelligent servo module for DIRECT SELECT) Affected functions: Drive position selection Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:270641Possible cause and remedy Internal fault in control unit Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**: - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**: - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**: - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**: - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...

Mercedes Benz

Search This Blog