Saturday, June 5, 2021

2010 Cadillac Truck SRX AWD V6-3.0L Page 1732

2010 Cadillac Truck SRX AWD V6-3.0L Page 1732



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



Note: If other DTCs are set, diagnose those DTCs first.



1. Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing



and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Transmission Fluid Level and Condition



Check) to verify correct fluid level and condition.



Note: Perform a scan tool snapshot during the road test.



2. Perform the Road Test (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Initial Inspection and



Diagnostic Overview). Verify the transmission operation performs as indicated, in the road test instructions.



3. Review the scan tool snapshot transmission data parameters. Verify the engine and transmission data parameters display the correct values in



all forward gear ranges:



* Engine Speed



* Transmission ISS



* Transmission OSS



* Vehicle Speed



* Shift Solenoid 1



* TFP Switch 1



* TFP Switch 3



* TFP Switch 4



* TFP Switch 5



4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component



Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Line Pressure Check). Verify the transmission line pressure gauge is



within the range specified in the Line PC Solenoid Valve Pressure table. Refer to Solenoid Valve Pressure (See: Specifications/Mechanical



Specifications/Automatic Transmission/Transaxle/System Specifications/6T70/6T75 - Automatic Transmission/Solenoid Valve Pressure).



瀚慖f not within the specified range, repair as necessary. Refer to Fluid Pressure High or Low (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Testing and Inspection/Symptom Related Diagnostic Procedures/6T70/6T75 - Automatic Transmission/Fluid



Pressure High or Low) for further diagnosis.



2. Ignition OFF, remove the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly



Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and



Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).



3. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (See: Transmission and



Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic



Transmission/Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test). Test all solenoids on the



control solenoid valve assembly. A pressure change should occur for each solenoid.



瀚慖f the control solenoid valve assembly does not pass the performance test, replace the control solenoid valve assembly.



4. Listed in the table below are conditions for each component that could set DTC P0751 or P0752. Carefully inspect each component for that



condition. Repair or replace as necessary.

No comments:

Post a Comment