Thursday, May 6, 2021

2010 Cadillac Truck SRX AWD V6-3.0L Page 1936

2010 Cadillac Truck SRX AWD V6-3.0L Page 1936



瀚慖f not the specified value, replace the Q6 Camshaft Position Actuator Solenoid Valve.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 1 (Right Side) Intake)



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust)



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 2 (Left Side) Intake)



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement, setup, and



programming



P2096



DTC P2096



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptor



DTC P2096



- Post Catalyst Fuel Trim System Low Limit



Circuit Description



Fuel trim bias is used by the engine control module (ECM) to keep the post catalyst HO2S voltage within a range of 580-665 mV. This allows



optimal catalyst efficiency under light load conditions, such as at idle or a steady cruise. The ECM constantly monitors how lean or rich the fuel



trim bias is commanded, to determine if the fuel trim bias is greater than a calibrated amount.



Conditions for Running the DTC



* Before the ECM can report DTC P2096, DTCs P0030, P0031, P0032, P0130, P0131, P0132, P0133, P0135, P0137, P0138, P0140, P0141,



P2232, P2235, P2270, P2271, P2272, and P2273 must run and pass.



* DTC P0100, P0101, P0102, P0103, P0111, P0112, P0113, P0116, P0117, P0118, P0119, P0420, P0443, P0458, or P0459 is not set.



* The engine speed is 1,080-3,480 RPM.



* The engine load is 17-20 % and steady.



* The Closed Loop fuel control is active for greater than 1 s.



* The front and rear HO2S are in Closed Loop.



* The calculated exhaust gas temperature is greater than 250掳C (482掳F).



* DTC P2096 runs continuously when the conditions above have been met for greater than 200 s.



Conditions for Setting the DTC



The lean correction limit for a condition causing a rich air/fuel mixture has been exceeded for a predetermined amount of time. The condition exists



for greater than 4 s or for a cumulative of 30 s.



Action Taken when the DTC Sets



DTC P2096 is a Type B DTC.



Conditions for Clearing the MIL/DTC

No comments:

Post a Comment