2010 Cadillac Truck SRX AWD V6-3.0L Page 2010

2010 Cadillac Truck SRX AWD V6-3.0L Page 2010

Altitude Versus Barometric Pressure (See: Powertrain Management/Computers and Control Systems/Specifications/Altitude Versus

Barometric Pressure).

瀚慖f the BARO pressure is not within the range specified for your altitude, refer to DTC P2227, P2228, or P2229 (LAU) ( See: P Code

Charts/P2227).

3. Engine at normal operating temperature, observe the Average Total Fuel Trim parameter with a scan tool. The Average Total Fuel Trim

should be between -22 to +23 percent.

瀚慖f not within the specified range, inspect for the following conditions:

* A mass air flow sensor signal that is skewed. If the Short Term Fuel Trim parameter changes greater than 20 percent when the MAF

sensor is disconnected, refer to DTC P0101 (LAU) (See: P Code Charts/P0101)DTC P0101 (LF1) (See: P Code Charts/P0101).

* A collapsed air intake duct

* A restricted air filter element-Refer to Air Cleaner Element Replacement (LF1) (See: Engine, Cooling and Exhaust/Engine/Tune-up and

Engine Performance Checks/Air Cleaner Housing/Air Filter Element/Service and Repair)Air Cleaner Element Replacement (LAU) (See:

Engine, Cooling and Exhaust/Engine/Tune-up and Engine Performance Checks/Air Cleaner Housing/Air Filter Element/Service and

Repair).

* The MAF sensor for foreign objects.

* Excessive fuel in the crankcase-Change the oil as necessary.

* Fuel contamination-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (See: Powertrain Management/Fuel Delivery and

Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool))Alcohol/Contaminants-in-Fuel

Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component

Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)) and Fuel System Cleaning (See:

Powertrain Management/Fuel Delivery and Air Induction/Service and Repair).

* The engine control module grounds for being clean, tight, and in the correct locations

* Rich injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Injector/Testing and Inspection).

* Restricted exhaust system-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and Exhaust/Exhaust System/Testing and

Inspection/Symptoms - Engine Exhaust).

* An engine mechanical condition-Refer to Symptoms - Engine Mechanical (See: Engine, Cooling and Exhaust/Engine/Testing and

Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

P2227

DTC P2227-P2229 or P2230 (LF1, LFW)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P2227

- Barometric Pressure (BARO) Sensor Performance

DTC P2228

- Barometric Pressure (BARO) Sensor Circuit Low Voltage

DTC P2229

- Barometric Pressure (BARO) Sensor Circuit High Voltage

DTC P2230

- Barometric Pressure (BARO) Sensor Circuit Erratic

Diagnostic Fault Information