2010 Cadillac Truck SRX FWD V6-3.0L Page 706

2010 Cadillac Truck SRX FWD V6-3.0L Page 706

Schematic Reference

Wiper/Washer Schematics (See: Wiper and Washer Systems/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Wiper/Washer System Description and Operation (See: Wiper and Washer Systems/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for diagnostic tester information

Circuit/System Verification

Operate the front washer by using the S80 Window Wiper/Washer Switch. Verify the G24 Windshield Washer Pump activates.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the X50A Fuse Block - Underhood.

2. Disconnect the harness connector X4 at the K9 Body Control Module.

3. Test for less than 5 ohm between the control circuit terminal 14 at the X50A Fuse Block - Underhood and the control circuit terminal 14 X4

at the K9 Body Control Module.

瀚慖f the value is not within the specified range, test the control circuit for a short to voltage or an open/high resistance.

瀚慖f the circuit tests normal, test or replace the K9 Body Control Module.

4. Test for infinite resistance between the control circuit terminal 14 at the X50A Fuse Block - Underhood and ground.

瀚慖f the value is not within the specified range, test the control circuit for a short to ground.

5. If all circuits test normal, test or replace the X50A Fuse Block - Underhood.

Component Testing

Relay Test

1. Ignition OFF, disconnect the harness connector X5 at the K9 Body Control Module.

2. Test for 60-200 ohm between control circuit terminal 14 X4 at the K9 Body Control Module and ground.

瀚慖f the value is not within the specified range, test the control circuit for a short to ground, short to voltage or an open.

瀚慖f all circuits test normal, test or replace the X50A Fuse Block - Underhood.

Output Control Tests

Ignition ON, command the Windshield Washer Relay Command ON and OFF with a scan tool. Observe that the KR11 Windshield Washer Pump

Relay clicks and the G24 Windshield Washer Pump runs.

If the KR11 Windshield Washer Pump Relay does not work, replace the X50A Fuse Block - Underhood.

If the KR11 Windshield Washer Pump Relay works, but the G24 Windshield Washer Pump does not run, test the washer fluid pump control circuit

and the washer fluid pump ground circuit.

If all circuits test normal, replace the G24 Windshield Washer Pump.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming

* Relay Replacement (Attached to Wire Harness) (See: Power and Ground Distribution/Power Distribution Relay/Service and Repair/Relay

Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (See: Power and Ground Distribution/Power