Skip to main content

2010 Cadillac Truck SRX AWD V6-3.0L Page 1398

2010 Cadillac Truck SRX AWD V6-3.0L Page 1398



DTC P0305



- Cylinder 5 Misfire Detected



DTC P0306



- Cylinder 6 Misfire Detected



Circuit/System Description



The engine control module (ECM) uses information from the crankshaft position sensor and the camshaft position sensors in order to determine



when an engine misfire is occurring. By monitoring variations in the crankshaft rotation speed for each cylinder, the ECM is able to detect



individual misfire events. A misfire rate that is high enough can cause 3-way catalytic converter damage. The malfunction indicator lamp (MIL)



will flash ON and OFF when the conditions for catalytic converter damage are present. DTCs P0301 through P0306 correspond to cylinders 1



through 6. If the ECM is able to determine that a specific cylinder is misfiring, the DTC for that cylinder will set, and the corresponding fuel



injector is disabled. The ECM will re-enable the fuel injector after 4 crankshaft revolutions when the misfire is not current. The ECM will re-enable



the fuel injector after 8 crankshaft revolutions when the misfire is not current, if the vehicle is equipped with a manual transmission.



Conditions for Running the DTC



* DTC P0010, P0011, P0013, P0014, P0016, P0017, P0018, P0019, P0020, P0021, P0023, P0024, P0068, P0101, P0102, P0103, P0106,



P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651,



P1516, P2101, P2122, P2123, P2127, P2128 or P2176 is not set.



* The engine speed is between 450-6,600 RPM.



* The evaporative emissions (EVAP) leak detection is not active.



* The delivered torque signal is greater than 5 % at idle.



* The delivered torque signal is between 6-29 % with the transmission in drive.



* The engine coolant temperature (ECT) is between -7 and +127掳C (+19 and +261掳F).



* The ECM is not receiving a rough road signal.



* The fuel level is greater than 11 %.



* The antilock brake system (ABS) and the traction control system (TCS) are not active or detecting rough road.



* Torque Converter Clutch (TCC) is not applied/active.



* The ECM is not in fuel cut-off or decel fuel cut-off mode.



* DTCs P0300 through P0306 run continuously when the above conditions exist for greater than 1,000 engine revolutions. 200 revolutions



after the first failure.



Conditions for Setting the DTC



P0300



The ECM detects a crankshaft rotation speed variation indicating a misfire rate sufficient to cause emissions levels to exceed a predetermined value.



P0301, P0302, P0303, P0304, P0305, P0306



The ECM detects a crankshaft rotation speed variation indicating a single cylinder misfire rate sufficient to cause emissions levels to exceed



mandated standards.



Action Taken When the DTC Sets



* DTCs P0300-P0306 are Type B DTCs.



* The ECM disables the fuel injector of the misfiring cylinder when a misfire is present.



Conditions for Clearing the DTC



DTCs P0300-P0306 are Type B DTCs.



Diagnostic Aids



* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect for the following possible sources:



- A tire or wheel that is out of round or out of balance



- Variable thickness brake rotors



- An unbalanced drive shaft



- Certain rough road conditions



- Transmission operation



- A damaged accessory drive component or belt; remove the belt and safely operate the engine to evaluate



* High resistance in the circuits of the injectors may set a misfire DTC without setting an injector DTC. Test the injector circuits of the affected



cylinder(s) for a high resistance if you suspect a condition.



* If the condition is intermittent, observing the scan tool IC Circuit Test and Fuel Injector Circuit Test Status parameters may help isolate the



condition. The circuit test status parameters will change from OK or Not Run to Fault if a condition exists.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...