Skip to main content

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1867

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1867

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

* DT-47825-10 Jumper Harness

* DT-48493 Jumper Harness

Circuit/System Verification

Test for correct operation of the Direction IMS in every range selection. Refer to Typical Scan Tool Data.

If the IMS operation matches the logic table, the system is functioning normally.

Circuit/System Testing

1. Disconnect the transmission X176 24-way connector. Ignition ON. The scan tool Direction IMS parameter should display HIGH for the R1,

R2, D1, D2 and S signal circuit displays.

瀚慖f a signal displays LOW, disconnect the PIM connector X1 and test the circuit for a short to ground.

瀚慖f the circuit tests normal, replace the PIM.

2. Install DT-48493 to the vehicle harness connector X176. Verify that a test lamp illuminates between the direction IMS switch ground circuit

and battery positive.

瀚慖f the test lamp does not illuminate, disconnect PIM connector X1 and test the ground circuit for an open, high resistance or short to

voltage condition.

瀚慖f the circuit tests normal, replace the PIM.

3. Connect a 3-amp fused jumper wire between each Direction IMS signal circuit at DT-48493 and the ground circuit terminal. The scan tool

parameter should display LOW for each signal circuit when grounded.

瀚慖f a scan tool parameter always displays HIGH, disconnect PIM connector X1 and test the circuit for an open, high resistance or short to

voltage condition.

瀚慖f the circuit tests normal, replace the PIM.

4. Disconnect the transmission 16-way X1 connector. Install DT-47825-10 to the vehicle harness. Connect a 3-amp fused jumper wire between

the Starter signal circuit terminal and ground. The scan tool parameter should display LOW when the signal circuit is grounded.

瀚慖f the scan tool parameter always displays HIGH, disconnect PIM connector X1 and test the circuit for an open, high resistance or short to

voltage condition.

瀚慖f the circuit tests normal, replace the PIM.

Important: The remaining diagnostic steps test the internal transmission components and circuits. The automatic transmission fluid

pan assembly must be removed in order to perform the diagnostic tests.

5. Disconnect the IMS connector at the switch.

Important: Connect one end of the DT-48493 to the transmission connector. Use the other end as the terminal testing point.

瀚慣est the direction signal circuits and the ground circuit between the IMS and the transmission 24-way X176 connector for a short to

ground, open, high resistance or short to voltage condition.

Important: Connect one end of the DT-47825-10 to the transmission connector. Use the other end as the terminal testing point.

瀚慣est the Starter signal circuit between the IMS and the transmission 16-way X1 connector for a short to ground, open, high resistance or

short to voltage condition. The TCM is a pass-through of the Starter signal circuit and should be tested as a typical circuit path.

瀚慖f the circuit, including the TCM, tests normal, replace the IMS switch.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM or TCM replacement, setup, and

Comments

Popular posts from this blog

2022 In a Kia 5 seater SUV, you’ll be ready to tackle them all.-More Detail in Description

via https://youtu.be/ReXWcwZMRQw

2010 Cadillac Truck SRX FWD V6-3.0L Page 1073

2010 Cadillac Truck SRX FWD V6-3.0L Page 1073 Circuit/System Verification Note: The engine oil level and the oil pressure are critical to the correct operation of the camshaft position actuator system. Verify that the engine has the correct oil level and the correct oil pressure before continuing with this diagnostic. 1. Ignition ON, observe the scan tool DTC information. Verify that none of the following DTCs are set. DTC P0016, P0017, P0018, P0019, P0335, P0336, P0338, P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, P0393, P0521, P0522, P0523, P0638, P2100, P2101, P2102, P2103, or P2119. 瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for further diagnosis. 2. Engine idling, command the appropriate Camshaft Position Actuator from 0 degrees to 40 degrees and back to zero while observing the appropriate scan tool Camshaft Position Vari...

2010 Cadillac Truck SRX AWD V6-3.0L Page 1544

2010 Cadillac Truck SRX AWD V6-3.0L Page 1544 Engine running, observe the scan tool Engine Oil Pressure Sensor parameter. The reading should be between 0.3-4.8 V. Circuit/System Testing 1. Ignition OFF, disconnect the harness connector at the B37B Engine Oil Pressure Sensor. 2. Ignition OFF, test for less than 10 ohm between the low reference circuit terminal 1 and ground. 瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20 Engine Control Module. 3. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 2 and ground. 瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K20 Engine Control Module. 瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 Engine Control Module. 4. Verify the scan to...

What is the most popular Camaro?

What is the most popular Camaro? What is the most popular Camaro?Here are the 10 best Camaros of all time, at least as far as we're concerned.1993 Chevrolet Camaro Z28. ... 2012 Chevrolet Camaro ZL1. ... 2010 Chevrolet Camaro SS. ... 1998 Chevrolet Camaro Z28 SS. ... 2019 Chevrolet Camaro ZL1. ... 1968 Chevrolet Camaro Z28. ... 1985 Chevrolet Camaro IROC-Z. ... 1971 Chevrolet Camaro SS.More items...•Aug 30, 2020Best Chevy Camaros of All Time - Top Speed What is the coolest muscle car? What is the coolest muscle car?The 10 best muscle cars of all time1964 Pontiac GTO.1970 Chevrolet Chevelle SS 454.1970 Plymouth Road Runner Superbird.1967 Chevrolet Camaro Z/28.1949 Oldsmobile Rocket 88.1965 Shelby Mustang GT-350.1968 Chevrolet Corvette L88.1964 Ford Fairlane Thunderbolt.More items...Top 10 best muscle cars | Auto Express What is the baddest muscle car? What is the baddest muscle car?10 Most Badass Muscle Cars, Ranked1 Dodge Charger R/T. Finally, coming in at first is the Dodg...

The Mercedes-AMG C63 is one of the best all-around high-performance luxury machines on sale today.

Can you spot the changes? The Mercedes-AMG C63 is one of the best all-around high-performance luxury machines on sale today. As a longtime rival to the BMW M3 and M4, Affalterbach and Munich continue to fight for bragging rights as to who builds the better car. To keep its rival on its feet, AMG revealed the refreshed 2019 AMG C63 S at New York last week. It’s not a complete redesign, but there are subtle exterior changes and one major mechanical upgrade. It can be hard to spot the differences between the 2018 the 2019 models, but we figured you'd be curious. Starting up front, the entire 2019 Mercedes-AMG C63 lineup (coupe, cabrio, and sedan) receives a new Panamericana grille, which replaces the previous horizontal bar. The three-point Silver Star proudly remains displayed front and center. But that new grille, in our opinion, fits the car better. The previous look was sort of meh, almost lazy. It’s like designers decided they had enough for the day and figured a single gri...

2019 Mercedes-Benz X-Class

Launched for the brand new 3-Series coupe and convertible and provided on all engine variants, M Sport cars include a raft of extra equipment as standard compared to an SE model. Furthermore, passive safety is offered thanks to standard tools akin to seven airbags and the i-Size attachment system for 2 little one seats. Standard safety gear includes antilock disc brakes, stability and traction management, aspect airbags, side curtain airbags, knee airbags and Mercedes-Benz's "mbrace" emergency telematics system. The SLS is supposed to be Mercedes-Benz's ultimate vehicle, however it is also meant to be extra affordable and sensible to drive than the now-discontinued Mercedes SLR McLaren. Twelve (more than one-third) of the above differences are in the double digits. Although the price is affordable or not, are the primary disadvantages of space and rear seats for Mercedes-Benz C-Class 220 CDI vibration motor in the city. In case your body kit includes entrance and/or r...

Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601 30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input

 Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601   30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input Topic number LI80.57-P-051521 Version 1 Design group 80.57 Drive authorization systems (DAS) Date 06-01-2011 Validity All 204, 207 model vehicles Reason for change Complaint 1. No crank / no start / intermittent no crank 2. Communication via SDS to Electronic Ignition Switch N73 (EIS/EZS), and or short test may or may not be possible at time of fault 3. Below scenario: ^ When accessing the occupants compartment, the message center in the ICM will illuminate (note: eventually the message center will time out and shut down, and will not illuminate until the CAN is activated via the interior lock/unlock switch). ^ The key will turn in EIS N73. ^ The ESL N26/5 does not activate/respond (or the steering wheel remains unlocked at all times). ^ The warning icons in the ICM will not il...

2010 Mercedes Benz C 300 (204.054) V6-3.0L (272.947) Page 2499

2.1.3.2.1.4. Check power supply at control unit N15/3 (ETC [EGS] control unit). Test 2.1.3.2.1.4.1: Guided test 2.1.3.2.1.4.1. Guided test Operation number of operation texts and work units or standard texts and flat rates:27-0641Possible cause - Battery has incorrect charge state or is faulty. - Local undervoltage of component N15/3 (ETC [EGS] control unit) Test sequence - Erase fault memory. Continue with button "F2" Warning!Communication with ECU required. 2.1.3.2.1.5. Check power supply at control unit N15/5 (Electronic selector lever module control unit). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test sequence - Switch off ignition. - Disconnect connector at component N15/5 (Electronic selector lever module control unit). - Switch on ignition. - [A.2] Measure direct voltage with multimeter between 2 and 1 [A.1] Status of relevant actual value: - Supply voltage (tml. 15):Warning! Communication with ECU required. Specified ...