Skip to main content

Disclaimer2010 Cadillac CTS Sedan AWD V6-3.0L Technical Service Bulletin # 09-08-48-002A Date: 090319

Disclaimer2010 Cadillac CTS Sedan AWD V6-3.0L Technical Service Bulletin # 09-08-48-002A Date: 090319



Body - Marks/Stains on Windshield When Wet



TECHNICAL



Bulletin No.: 09-08-48-002A



Date: March 19, 2009



Subject:



Marks/Stains on Windshield When Wet (Clean Windshield)



Models:



2010 and Prior Passenger Cars and Trucks (Including Saturn and Saab)



2010 and Prior HUMMER H2, H3



2010 Cadillac CTS Sedan AWD V6-3.0L Page 170



Supercede:



This bulletin is being revised to update the models and model years. Please discard Corporate Bulletin Number 09-08-48-002 (Section 08 - Body



and Accessories).



Condition



Some owners may comment that marks/stains appear on the windshield when the windshield is wet.



Cause



This condition may be caused by contact between the windshield and the vacuum hoses or other tools used in the assembly process. This contact



may leave a residue that creates a water repellent surface on the glass which, in wet conditions, appear as marks/stains on the surface.



Correction



Important



DO NOT REPLACE THE WINDSHIELD FOR THIS CONDITION.



To clean the windshield, use Eastwood Glass Polishing Compound*. Follow the manufacturer's directions for product use. Use only hand tools. DO



NOT USE POWER TOOLS.



Parts Information



Eastwood Glass Polishing Compound



1-800-343-9353 (for overseas inquiries: +1-610-705-2200)



http://www.eastwoodco.com/



*We believe this source and their products to be reliable. There may be additional manufacturers of such products. General Motors does not



endorse, indicate any preference for or assume any responsibility for the products from this firm or for any such items which may be available from



other sources.



Warranty Information



For vehicles repaired under warranty, use the table above.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...