Wednesday, September 2, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1910

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1910



瀚慖f any other DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic



Trouble Code (DTC) List - Vehicle) to diagnosis the applicable DTC.



2. Ignition ON, observe the barometric pressure (BARO) sensor pressure parameter and compare the reading on the scan tool to the barometric



pressure table. Refer to Altitude Versus Barometric Pressure (See: Powertrain Management/Computers and Control Systems/Specifications



).



瀚慖f the BARO sensor pressure is not within the range specified for your altitude, refer to DTC P2227, P2228, or P2229 (LLT) ( See: P



Code Charts/P2227).



3. Engine at normal operating temperature, observe the scan tool Long Term Fuel Trim parameters. The LT FT Cruise/Accel parameters should



be less than 33 %. The LT FT Idle/Decel parameters should be less than 7 %.



瀚慖f not within the specified range, verify none of the following conditions exist:



* The heated oxygen sensor (HO2S) is installed securely and the electrical connector is not contacting the exhaust system.



* Missing, restricted, or leaking exhaust components-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and Exhaust/Exhaust



System/Testing and Inspection/Symptoms - Engine Exhaust).



* The air intake system after the MAF sensor for vacuum leaks



* A mass air flow (MAF) sensor signal that is skewed-If the Short Term FT parameters for both banks changes greater than 20 % when the



MAF sensor is disconnected, refer to DTC P0101 (w/LLT) (See: P Code Charts/P0101)DTC P0101 (LF1) (See: P Code Charts/P0101).



* Fuel contamination-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool) (See: Powertrain Management/Computers



and Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (with



Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (without Special Tool) (See: Powertrain Management/Computers and Control



Systems/Testing and Inspection/Component Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (without Special



Tool)) and Fuel System Cleaning (See: Powertrain Management/Fuel Delivery and Air Induction/Service and Repair).



* Splits, kinks, or improper connections at the vacuum hoses



* The fuel system is operating lean. Refer to Fuel System Diagnosis (See: Powertrain Management/Computers and Control



Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel System Diagnosis).



* Vacuum leaks at the intake manifold or throttle body



* Leaking crankcase ventilation system



* The engine control module grounds for being clean, tight, and in the correct locations



* A high engine oil level condition-A high engine oil level causes oil residue to form on the mass air flow (MAF) sensor, causing a lean



indication. The MAF sensor does not need to be replaced.



* Vacuum leaks that only affect one bank of the engine-For example, the intake manifold, the injector O-rings.



* Lean injectors-Refer to Fuel Injector Solenoid Coil Test (w/LLT) (See: Powertrain Management/Computers and Control



Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Solenoid Coil Test)Fuel Injector Solenoid Coil



Test (w/LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection).



* An engine mechanical condition-Refer to Symptoms - Engine Mechanical (See: Engine, Cooling and Exhaust/Engine/Testing and



Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).



4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



P2188



DTC P2178, P2180, P2188, or P2190 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P2178



- Fuel Trim System Rich at Cruise or Acceleration Bank 1



DTC P2180



- Fuel Trim System Rich at Cruise or Acceleration Bank 2

No comments:

Post a Comment