2010 Cadillac Truck SRX AWD V6-3.0L Page 656

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

B3205 00, B3205 39, B3205 42, B3210 00, B3210 39, B3210 42, B3215 39, B3220 39

1. Ignition ON, command the M74 window motor UP and DOWN with a scan tool. The M74 window motor should perform the UP and

DOWN functions.

Note: If the window performs the UP and DOWN functions, clear the DTC

2. Replace the M74 window motor with a M74 window motor compatible for that specific make and model vehicle.

Circuit/System Testing

B3205 4B, B3210 4B

1. Ignition ON, starting with the window completely UP, press and hold the appropriate power window switch until the window is fully open

and continue holding the switch down for approximately 5 seconds after the window is completely open.

2. Pull the power window switch up until the window is fully closed and continue holding the switch up for approximately 5 seconds after the

window is completely closed.

3. Command the window to express UP and express DOWN by pressing the window switch past the first detent and releasing and then pulling

the window switch past the first detent and releasing. The window should perform the express UP and express DOWN functions.

瀚慖f the M74 window motor does not perform as specified and the DTC resets, replace the M74 window motor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Front Side Door Window Regulator Replacement (See: Windows and Glass/Windows/Service and Repair/Front Side Door Window

Regulator Replacement)

* Rear Side Door Window Regulator Motor Replacement (See: Windows and Glass/Windows/Service and Repair/Rear Side Door Window

Regulator Motor Replacement)

B3410

DTC B3410 or B3420

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B3410 01

- Automatic Headlamp Leveling Control Module Front Axle Sensor Signal Circuit Short to Battery

DTC B3410 06

- Automatic Headlamp Leveling Control Module Front Axle Sensor Signal Circuit Low Voltage/Open

DTC B3420 01

- Automatic Headlamp Leveling Control Module Rear Axle Sensor Signal Circuit Short to Battery

DTC B3420 06

- Automatic Headlamp Leveling Control Module Rear Axle Sensor Signal Circuit Low Voltage/Open

Diagnostic Fault Information

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V86.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: A80 (Intelligent servo module for DIRECT SELECT) Affected functions: Drive position selection Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:270641Possible cause and remedy Internal fault in control unit Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**: - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**: - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**: - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**: - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...

Mercedes Benz

Search This Blog