Skip to main content

2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 08-08-45-002A Date: 100514

2010 Cadillac Truck Escalade RWD V8-6.2L Technical Service Bulletin # 08-08-45-002A Date: 100514

Body - L/H/R/H Power Mirror(s) Inoperative

TECHNICAL

Bulletin No.: 08-08-45-002A

Date: May 13, 2010

Subject: Left Or Right Power Outside Mirror Inoperative (Inspect Wire Harness)

Models:

2007-2010 Cadillac Escalade, Escalade ESV, Escalade EXT

2007-2010 Chevrolet Avalanche, Silverado, Suburban, Tahoe

2007-2010 GMC Sierra, Sierra Denali, Yukon, Yukon Denali, Yukon XL, Yukon Denali XL

Supercede:

This bulletin is being revised to add the 2010 model year and update the Warranty Information. Please discard Corporate Bulletin Number

08-08-45-002 (Section 08 - Body and Accessories).

Condition

Some customers may comment that the left or right outside power mirror is inoperative.

Cause

This condition may be caused by two different concerns.

1. The wiring harness may be damaged from a screw that retains the door trim to the door.

2. The wiring harness connector at the mirror glass actuator may not be locked in place.

Correction

Inspect the wiring harness and connector.

1. Remove the door trim and inspect the wiring harness. Refer to Front Side Door Trim Panel Replacement in SI if necessary. If the harness is

damaged , refer to Repairing Damaged Wire Insulation in SI. After making the repair, reposition the harness.

2. Inspect the connector at the mirror actuator. Refer to Outside Rearview Mirror Motor Replacement in SI if necessary. If the connector is

loose, remove and reinstall the connector.

Warranty Information

2010 Cadillac Truck Escalade RWD V8-6.2L Page 310

For vehicles repaired under warranty, use the table above.

Comments

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...

D138, Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...